Quick answer: Snow blower maintenance is mostly a once-a-year job before the first snow, plus a few checks every time you use it. The Toro Power Max 824 OE, Ariens Deluxe, MTD-built Cub Cadet and Troy-Bilt, Honda HSS and Husqvarna ST manuals all list an oil change on a set schedule, a spark plug check, lube points, and checks of the skids, belts and cables. The intervals differ by maker, so match your brand in the tables below.
Jump to the table: How often: the short version ↓
- Every use: check the engine oil level and look for loose bolts or broken shear pins. After you finish, run the auger a few minutes and knock off snow and ice.
- Before the first snow, every year: change the oil if it’s due, check or replace the spark plug, grease and oil the lube points, check the auger gearbox (Toro, Ariens), skid shoes, scraper, belts, cables and tires, then test start it.
- End of the season: stabilize or drain the fuel, lubricate, and clean it.
Find your brand: Toro · Ariens · Cub Cadet, Troy-Bilt, Craftsman · Honda · Husqvarna · Briggs and Tecumseh engines · Spark plug and gap

Safety first, every time. Shut off the engine, remove the key and pull the spark plug wire before any maintenance, and let the engine cool (Toro manual, p. 18; MTD engine manual, p. 12).
Every interval below is printed in the maker’s operator’s manual, linked with the page. Where a manual says nothing, we say “not listed” instead of filling the gap.
How often: the short version
| Task | Most manuals say | Exceptions |
|---|---|---|
| Check engine oil | Before each use | None. All six makers ask for it |
| First oil change | After the first 5 hours | 2 h: Toro Power Clear, SnowMaster, Tecumseh. First month: Ariens engine. First month or 20 h: Honda. 20 h: Husqvarna |
| Regular oil change | Once a year or each season | Ariens engine: every 6 months. MTD: season or 50 h. Briggs: 25 h or yearly. Tecumseh: 25 h or 3 months. Husqvarna: every 100 h |
| Spark plug | Check yearly, replace about every 100 h | Ariens engine: replace yearly. Briggs: 25 h or yearly. Tecumseh: 200 h. Honda: 300 h or 4 years |
| Auger gearbox | Check the oil yearly (Toro, Ariens) | Honda: dealer item. Husqvarna: “not necessary.” MTD: not listed |
| Lube points | Each season or every 25 h | Honda: before storage. Toro Power Max: hex shaft yearly |
| Shear pins and bolts | Check before each use | Honda lists shear bolts each use. Ariens, Husqvarna: fasteners each use. Toro Power Max 824 OE lists none |
| Belts and cables | Check yearly | Toro, Honda, Husqvarna: belts go to a dealer |
| Skid shoes and scraper | Check yearly | Honda: each use too. Husqvarna: scraper before each use |
| Tire pressure | Check yearly | Toro 17 to 20 psi. Honda 20 psi. Husqvarna 18 or 20 psi max. Ariens, MTD: tire sidewall |
Oil grades and amounts are in our snow blower oil guide. End-of-season fuel rules are in our gas and fuel stabilizer guide.
Snow blower maintenance schedule by brand
Toro
From the Toro Power Max 824 OE operator’s manual (form 3415-760). Other Toro two-stage manuals use the same layout.
| Task | When | What the manual says (page) |
|---|---|---|
| Check engine oil | Before each use | Add oil if needed (p. 18) |
| Change engine oil | First 5 h, then yearly | Grade and amount: see oil guide (pp. 18, 22) |
| Traction and auger cables | First 2 h, then yearly | Inspect and adjust or replace (pp. 18, 20 to 21) |
| Spark plug | Every 100 h | Champion RN9YC or NGK BPR6ES, gap 0.030 in (p. 23) |
| Skids and scraper | Yearly | Check and adjust (pp. 18 to 19) |
| Auger gearbox oil | Yearly | 3/8 in below the filler, GL-5 or GL-6 SAE 80-90 EP, no synthetic (p. 21) |
| Hex shaft | Yearly | Light coat of automotive engine oil. None on the rubber wheel or friction pulley (p. 22) |
| Tires | Yearly or before storage | 17 to 20 psi (116 to 137 kPa) (p. 18) |
| Belts | Yearly or before storage | An Authorized Service Dealer inspects and replaces them (p. 18) |
| Fuel | End of season | Drain it and run the engine dry (p. 18) |
Toro single-stage and SnowMaster. The Power Clear 721 R/E changes oil after the first 2 hours, then yearly, and services the plug yearly. A dealer inspects its drive belt (manual 3423-722, pp. 12, 15). The SnowMaster 724 and 824 QXE change oil after 2 hours, then yearly, and replace the plug every 100 hours (manual 3432-529, pp. 14, 17). Toro CCR two-cycle models have no oil change because they run on a 50:1 gas and oil mix. Our oil guide has the mix.
Ariens
From the Ariens Deluxe manual (30219300A, page EN-14) and the Ariens snow engine manual (PGM45009, p. 13). The two disagree on oil, so both are shown.
| Task | When | What the manual says (page) |
|---|---|---|
| Clutches, handle interlock, fasteners | Each use | Check the auger and drive clutch operation (EN-14) |
| Check engine oil | Each use | See the engine manual (EN-14) |
| Change engine oil | First month, then every 6 months | Engine manual. Every 40 h if you run it over 40 h a year (p. 13). The machine manual marks it “annually” (EN-14) |
| Spark plug | Clean every 6 months, replace yearly | F6RTC, gap 0.027 to 0.030 in (pp. 12 to 13). Machine manual: “as needed” |
| Tire pressure | Every 25 h and yearly | Use the pressure on the tire sidewall (EN-14, EN-15) |
| Grease fittings | Every 25 h and yearly | Ariens Hi-Temp Grease or equivalent (EN-14, EN-16) |
| Auger gearcase oil | Every 25 h and yearly | 2.4 to 2.6 in below the cover’s flat surface. Ariens recommends its L3 synthetic gear lube (EN-16) |
| Fuel | Every fill | Add fuel stabilizer to all fuel (EN-14, EN-25) |
The Ariens lube points (EN-16, Figures 11 and 12) are on the traction drive under the bottom cover. The chute isn’t one of them. Ariens warns: don’t let grease or oil touch the friction disc, friction plate or belts. For belt work, Ariens points you to the service manual for your unit (EN-24).
Cub Cadet, Troy-Bilt and Craftsman (MTD-built)
From the MTD 357cc and 420cc engine manual (769-26922, p. 12) and the 2- and 3-stage machine manual (769-26795). The 179cc to 243cc engine manual (769-11570, p. 13) has the same schedule.
| Task | When | What the manual says (page) |
|---|---|---|
| Check engine oil | Each use or every 5 h | (p. 12) |
| Change engine oil | First 5 h, then every season or 50 h | (p. 12) |
| Spark plug | Check every season or 25 h, replace every season or 100 h | Part 951-10292 (pp. 12, 18) |
| Shroud and muffler area | Each use or every 5 h | Clean (p. 12) |
| Auger control cable | Before operating | Very little slack. The auger must stop fully when released (769-26795 p. 17) |
| Auger shaft | At least once a season | Remove the shear pins, spray lubricant inside the shaft (p. 29) |
| Wheel axles | At least once a season | Multipurpose automotive grease (p. 28) |
| Side chute control | Once a season | 3-in-1 oil on the eye-bolt bushing and spiral (p. 28) |
| Hex shaft (non-hydro) | Every season or 25 h | Light coat of Bostik Never-Seez. None on the drive plate or friction wheel (p. 28) |
| Auger gearbox | Not listed in the manual | 769-26795 prints no gearbox service |
| Belts | When worn | Auger belt is a DIY job (pp. 29 to 30). Drive belt goes to a dealer (p. 30) |
| Tire pressure | Before operating | Use the psi on the tire sidewall (p. 15) |
Craftsman owners: Craftsman snow blowers have used engines from different makers. Read the label on your engine and use that maker’s row: MTD here, or Briggs and Tecumseh below. We didn’t find a Craftsman document that prints its own spark plug number.
Honda
From the Honda HSS724A owner’s manual (00X31V45 A089, p. 14). The HSS928A and HSS1332A schedule (A130, p. 42) uses the same intervals.
| Task | When | What the manual says (page) |
|---|---|---|
| Check engine oil | Each use | (p. 14) |
| Change engine oil | First month or 20 h, then yearly or every 100 h | Change before the season (p. 14) |
| Spark plug | Check yearly, replace every 300 h or 4 years | NGK BPR5ES or DENSO W16EPR-U, gap 0.028 to 0.031 in (p. 15) |
| Auger transmission oil | Yearly, before the season | Dealer item (p. 14) |
| Skid shoes and scraper | Each use and yearly | Flip a skid shoe when worn to 0.02 in (pp. 14, 16) |
| Shear bolts, bolts and nuts | Each use | (p. 14) |
| Tires | Each use and before storage | 20 psi (138 kPa). Don’t go over (p. 16) |
| Cables and belts | First month or 20 h, then yearly | Dealer items unless you have the tools and skills (p. 14) |
| Lube points | Before storage | Grease the chute guide, chute gear and levers. Hondalube spray on track chains (p. 18) |
| Fuel | Before storage | Drain the tank and carburetor (pp. 14, 18) |
Husqvarna
From the Husqvarna ST 224, 227P, 230P and 224P operator’s manual (694-003, p. 15).
| Task | When | What the manual says (page) |
|---|---|---|
| Nuts, screws, oil level, leaks | Daily | Clear the auger too (p. 15) |
| Change engine oil | After 20, 50 and 100 h, then every 100 h | (p. 15) |
| Spark plug | Clean before use each year, change every 100 h | F6RTC or F7RTC, gap 0.030 in (pp. 15, 24) |
| Tire pressure | Every 50 h | 18 psi max (ST 224, 227P, 224P), 20 psi max (ST 230P) (pp. 15, 24) |
| Gearbox | Never | “It is not necessary to add grease or to do other maintenance to the gearbox” (p. 15) |
| Interlock bosses | Each season or every 25 h | Small amount of lithium grease. Oil the pivot points (p. 16) |
| Augers and scraper bar | Before each use | Reverse the scraper bar when one edge wears (p. 16) |
| Belts | When they slip | Not adjustable. A service center replaces both together (p. 18) |
Briggs & Stratton and Tecumseh engines
These engines turn up on Craftsman, Murray, Simplicity and many older machines. Tecumseh no longer makes engines, so this row is for older snow blowers.
| Task | Briggs Snow Series (80024465) | Tecumseh Snow King (181-1275-14) |
|---|---|---|
| Check oil | Before each use (p. 13) | Every 5 h or before each use (p. 26) |
| First oil change | After 5 h (p. 13) | After 2 h, engine warm (p. 26) |
| Regular oil change | Every 25 h or yearly (p. 13) | Every 25 h or 3 months (p. 26) |
| Spark plug | Replace every 25 h or yearly, dealer service (p. 13) | Check 100 h or seasonally, replace 200 h or seasonally (p. 26) |
| Other checks | Every 25 h or yearly: scraper, rubber auger, hardware, auger cable, muffler (p. 13) | Clean the cooling fins every 5 h (p. 26) |
The Briggs manual adds an after-each-use step: clear snow and slush off the controls, wheels, chute and auger (p. 13).
Spark plug and gap by engine
Find your engine, then use the plug and gap its manual prints. Gaps differ, even inside one maker’s lineup, so don’t use one number for every snow blower.
| Engine or machine | Plug the manual names | Gap | Check or replace (page) |
|---|---|---|---|
| Toro Power Max 824 OE | Toro, or Champion RN9YC or NGK BPR6ES | 0.030 in (0.76 mm), new plug | Replace every 100 h (pp. 18, 23) |
| Toro SnowMaster 724, 824 QXE | Toro, or Champion RN9YC or NGK BPR6ES | 0.030 in (0.76 mm), new plug | Replace every 100 h (pp. 14, 17) |
| Toro Power Clear 721 R/E | NGK BPR6ES or Champion RN9YC | 0.030 in (0.76 mm) | Service yearly (pp. 12, 15) |
| Ariens snow engine (AX) | F6RTC. Ariens lists Champion RN9YC and NGK BPR6ES as cross-references | 0.027 to 0.030 in | Clean every 6 months, replace yearly (pp. 12 to 13) |
| MTD 357cc and 420cc (Cub Cadet, Troy-Bilt) | MTD 951-10292 | 0.030 to .06 in (0.76 to 1.5 mm), as printed | Check every season or 25 h, replace every season or 100 h (pp. 12, 13, 18) |
| MTD 179cc, 208cc, 243cc | MTD 951-10292 | 0.030 in (0.76 mm) in the text | Same as above (pp. 13, 15, 20) |
| Honda HSS724A, HSS928A, HSS1332A | NGK BPR5ES or DENSO W16EPR-U | 0.028 to 0.031 in (0.7 to 0.8 mm) | Check yearly, replace every 300 h or 4 years (A089 pp. 14 to 15) |
| Husqvarna ST 224, 227P, 230P, 224P | F6RTC or F7RTC | 0.030 in (0.762 mm) | Clean yearly, change every 100 h (pp. 15, 24) |
| Briggs & Stratton Snow Series | Not listed in the manual | .030 in (0.76 mm) | Replace every 25 h or yearly (pp. 13, 18) |
| Tecumseh Snow King | A resistor plug from a Tecumseh dealer. No number listed | .030 in (0.76 mm) | Replace every 200 h or seasonally (pp. 21, 26) |
About the MTD numbers. We rendered both MTD pages to check them. The 357cc and 420cc manual really does print “0.030 – .06 in. (0.76 – 1.5 mm)” (769-26922, p. 13). The 179cc to 243cc manual’s text says 0.030 in (0.76 mm), but its drawing on the same page is labeled “0.06-0.03 in. 0.60-0.80 mm” (769-11570, p. 15). Both include 0.030 in. If you’re unsure, ask an MTD dealer for your engine’s spec.
Checking and gapping the plug:
- Let the engine cool, then pull the plug wire or boot (Toro p. 23).
- Remove the plug with a spark plug wrench.
- Replace it if the insulator is cracked or the electrodes are worn, pitted, burned or fouled (MTD p. 13). Toro says to discard the old plug and gap a new one. MTD allows a wire-brush cleaning if you reuse it.
- Measure the gap with a feeler gauge and bend only the side electrode to adjust it (MTD p. 13).
- Thread it in by hand so it doesn’t cross-thread, then tighten. Ariens says 1/4 turn after the plug seats (p. 12). Briggs lists 180 lb-in (20 Nm) (p. 18).
Honda warns that a plug with the wrong heat range can damage the engine (p. 15), and Ariens says the same about an incorrect plug (p. 12). The “equivalent” plugs above are the makers’ own cross-references. We don’t list other plug brands. If the plug looks fine and the engine still won’t fire, work through our snow blower won’t start guide.
Pre-season checklist (snow blower tune-up)
What a snow blower tune-up includes
- Oil: change it if it’s due, and check the level either way. Grade and amount by engine: snow blower oil.
- Spark plug: check the gap or replace it, using the plug table.
- Fuel: start the season on fresh gas. Rules by maker: snow blower gas and stabilizer.
- Shear pins or bolts: look for broken ones and keep OEM spares. Find yours with our shear pin lookup.
- Belts and auger cable: check for wear and slack. Part numbers are in our belt guide, and auger cable checks are in auger not turning.
- Drive: if it won’t pull itself along, check the drive side with our snow blower won’t move guide.
- Lube points: grease and oil them as your brand table says. Keep lube off friction discs, friction wheels and belts.
- Gearbox: check the oil on Toro and Ariens machines. It’s a dealer job on Honda, and Husqvarna says it isn’t needed.
- Skid shoes and scraper: set the height and flip or reverse worn parts. Settings for gravel are in our gravel driveway guide.
- Tires: Toro Power Max 17 to 20 psi, Honda 20 psi, Husqvarna 18 or 20 psi max. Ariens and MTD: the tire sidewall.
- Test start outdoors: follow our how to start a snow blower steps. If it surges or leaks gas, see carburetor cleaning.
Snow blower chute won’t turn
First, the safety part: shut off the engine, remove the key and wait for everything to stop. Never put a hand in the chute. Use the clean-out tool (Toro p. 16).
Ice is the usual cause. Toro says not to force frozen controls. Start the engine and let it run a few minutes instead (p. 17). To prevent it, let the engine run a few minutes after you finish, run the auger to clear snow out of the housing, and turn the chute control so it doesn’t freeze in place (Toro p. 17; Ariens EN-25).
If it isn’t frozen, it’s usually an adjustment or a dry pivot. Here’s what each manual says.
| Brand | How the chute turns | Lube point (page) | If it sticks (page) |
|---|---|---|---|
| Toro Power Max 824 OE | Joystick (Quick Stick) and cable | Not listed in the schedule (p. 18) | Adjust the discharge-chute latch (pp. 15, 24). Route the cable inside the handles (p. 15) |
| Ariens Deluxe | Chute rotation handle | Not listed. The lube figures cover the drive only (EN-16) | Won’t stay put: tighten the nut on the carriage bolt (EN-19). Deflector: nut under the panel, cable nuts (EN-18) |
| Cub Cadet, Troy-Bilt (MTD) | Side rod with a spiral, overhead, or electric joystick | Side rod: 3-in-1 oil on the eye-bolt bushing and spiral, once a season (p. 28) | Spiral slips: move the bracket (p. 16). Overhead drifts: tighten the preload nut 1/4 turn at a time (p. 16) |
| Honda HSS | Electric chute control switch | Grease the chute guide washers and chute gear before storage (p. 18) | Chute guide control cable is a dealer item (p. 14) |
| Husqvarna ST | Chute control lever | Oil the pivot points (p. 16) | Not listed in the manual |
Electric chutes: Honda’s chute switch only works with the engine running, and the chute moves faster at full throttle (p. 8). On MTD joystick models, you can switch the chute to manual rotation with the cotter pin on the chute control head (769-26795 p. 23).
Chute turns fine but no snow comes out? That’s a clog or an auger problem. See snow blower auger not turning.
End-of-season checklist
- Clear it out: run the auger a few minutes to throw out loose snow, then wipe off snow and ice (Toro p. 17; Ariens EN-25).
- Fuel: Toro says drain it and run the engine dry, and Husqvarna says empty the tank. Ariens, MTD and Honda say stabilize for short breaks and drain for longer ones. Details by brand: gas and fuel stabilizer guide.
- Lubricate: do the season’s lube points (MTD p. 28; Honda p. 18; Ariens EN-25).
- Clean and protect: wash off salt with mild soap and low-pressure water, touch up paint, and put light oil or anti-rust on bare metal (Ariens EN-25). MTD says to coat the machine with light oil or silicone if the room isn’t ventilated (p. 28).
- Put it somewhere dry: Ariens says cool, dry and not outdoors (EN-25). Husqvarna says dry and frost-free (p. 24).
DIY or dealer?
| Brand | Manual sends to a dealer (page) | Manual has you do it (page) |
|---|---|---|
| Toro Power Max 824 OE | Both belts (pp. 18, 24) | Oil, plug, gearbox oil, hex shaft, skids, cables (pp. 18 to 23) |
| Ariens Deluxe | Engine service: the engine maker’s service center (EN-14). Belts: service manual (EN-24) | Clutch checks, grease, gearcase oil (EN-14 to EN-16) |
| Cub Cadet, Troy-Bilt (MTD) | Drive belt (p. 30) | Auger belt, lube points, shear pins (pp. 26 to 30) |
| Honda HSS | Auger transmission oil, cables, belts, unless you have the tools and skills (p. 14) | Oil, plug, skid shoes, shear bolts, lube (pp. 14 to 18) |
| Husqvarna ST | Belts and worn auger edges (pp. 16, 18) | Oil, plug, scraper bar, lube (pp. 15 to 16) |
| Briggs Snow Series | Spark plug and valve clearance. Briggs suggests a dealer for all maintenance (p. 13) | Oil, scraper and auger checks (p. 13) |
Same engines, summer side: see lawn mower maintenance.
FAQ
How often should a snow blower be serviced? Once a year before the first snow, plus an oil check every time you use it. The Toro Power Max 824 OE, Honda HSS and MTD manuals also ask for a first oil change after the break-in hours (5 h for Toro and MTD, first month or 20 h for Honda). Ariens’ engine manual asks for an oil change every 6 months. Your brand’s table above has the full list.
What does a snow blower tune-up include? Oil, spark plug, fresh fuel, shear pins, belts and cables, lube points, gearbox oil where the maker lists it, skid shoes and scraper, tires, and a test start outdoors. The pre-season checklist above links each step to its guide.
What spark plug does my Toro, Ariens or Craftsman snow blower use? Toro’s Power Max 824 OE and SnowMaster manuals name a Toro plug or Champion RN9YC or NGK BPR6ES. Ariens’ snow engine manual recommends an F6RTC and lists RN9YC and BPR6ES as cross-references. Craftsman machines use different engines, so read the engine label: the MTD 357cc and 420cc engine manual lists part 951-10292.
What is the spark plug gap on a snow blower? It depends on the engine. Toro, Husqvarna, Briggs and Tecumseh manuals print 0.030 in. Honda HSS prints 0.028 to 0.031 in, and Ariens prints 0.027 to 0.030 in. The MTD 357cc and 420cc manual prints a range of 0.030 to .06 in. Use the plug table for your engine.
Does a snow blower gearbox need oil or grease? The makers disagree. Toro checks it yearly with GL-5 or GL-6 SAE 80-90 EP gear oil and says no synthetic. Ariens checks it every 25 hours or yearly and recommends its own L3 synthetic gear lube. Honda makes the auger transmission oil a dealer item, Husqvarna says no gearbox maintenance is needed, and the MTD machine manual doesn’t list one.
How do I lubricate a snow blower? Use what your manual names, where it names it. Toro uses automotive engine oil on the hex shaft yearly. Ariens uses Hi-Temp Grease on the fittings every season or 25 hours. MTD uses 3-in-1 oil on the chute spiral, grease on the axles and Never-Seez on the hex shaft. Honda greases the chute gear and levers before storage. Keep lube off friction discs, friction wheels and belts.
What can I spray on the chute so snow doesn’t stick? None of the operator’s manuals we checked recommends a non-stick chute spray. MTD and Ariens only mention light oil, silicone or anti-rust for rust protection in storage. If your chute keeps packing up, see the clog section of our auger not turning guide.
How often should I change snow blower oil? Most manuals say once a year or each season, after a first change at 2 to 20 hours. Grades, amounts and every engine’s interval are in our snow blower oil guide.
Sources
- Toro, Power Max 824 OE Operator’s Manual 3415-760 (chute, p. 15; clogs, p. 16; freeze-up, p. 17; maintenance schedule, p. 18; skids, p. 19; cables and gearbox, p. 21; hex shaft and oil, p. 22; spark plug, p. 23; chute latch and belts, p. 24)
- Toro, Power Clear 721 R/E Operator’s Manual 3423-722 (maintenance schedule, p. 12; spark plug, p. 15)
- Toro, SnowMaster 724 QXE and 824 QXE Operator’s Manual 3432-529 (maintenance schedule, p. 14; spark plug, p. 17)
- Ariens, Deluxe Sno-Thro Operator’s Manual 30219300A (maintenance schedule, p. EN-14; tires and service parts, p. EN-15; gearcase and lubrication, p. EN-16; chute and deflector, pp. EN-18 to EN-19; troubleshooting, p. EN-24; storage, p. EN-25)
- Ariens, Snow Engine Operation Manual PGM45009 (spark plug, p. 12; maintenance schedule, p. 13)
- MTD, 357cc and 420cc OHV Engine Operator’s Manual 769-26922 (2023; maintenance schedule, p. 12; spark plug, p. 13; replacement parts, p. 18)
- MTD, 179cc, 208cc and 243cc OHV Engine Operator’s Manual 769-11570 (maintenance schedule, p. 13; spark plug, p. 15; replacement parts, p. 20)
- MTD, 2- and 3-Stage Snow Blower Operator’s Manual 769-26795 (2023; tires, p. 15; chute controls, p. 16; auger control, p. 17; electric chute, p. 23; shear pins, p. 26; lubrication and storage, p. 28; auger shaft and belts, pp. 29 to 30)
- Honda, HSS724A Owner’s Manual 00X31V45 A089 (chute control switch, p. 8; maintenance schedule, p. 14; spark plug, p. 15; tires and skid shoes, p. 16; storage lubrication, p. 18)
- Honda, HSS928A / HSS1332A Owner’s Manual 00X31V45 A130 (maintenance schedule, p. 42; spark plug, pp. 49 to 50)
- Husqvarna, ST 224 / ST 227P / ST 230P / ST 224P Operator’s Manual (2019; chute, p. 11; maintenance schedule, p. 15; lubrication and scraper, p. 16; belts, p. 18; storage and technical data, pp. 23 to 24)
- Briggs & Stratton, Snowthrower Operator’s Manual 80024465 (maintenance schedule, p. 13; specifications, p. 18). Retailer-hosted copy (Home Depot)
- Tecumseh, 4-Cycle Snow King Engine Operator’s Manual 181-1275-14 (spark plug, p. 21; maintenance intervals, Table 4, p. 26). Archive copy
Related guides: Snow blower won’t start · Snow blower won’t move · Auger not turning · Shear pin lookup · Belt part numbers · Snow blower oil · Gas and stabilizer · Gravel driveway settings · How to start a snow blower · Carburetor cleaning · Plowing snow with a tractor



