Quick answer: If the engine runs and the impeller still throws snow but the auger stopped turning, or one side of the auger spins loose on its shaft, a shear pin has probably snapped. Shear pins (many makers call them shear bolts) are soft bolts built to break when the auger hits ice, a rock or a newspaper, so your gearbox doesn’t. Shut the engine off, pull the key and the spark plug wire, and replace the broken pin with the exact OEM part for your model. Never use a hardware-store bolt. Find your pin’s part number in the lookup below.
Jump to the shear pin part-number lookup ↓
YardGuides may earn a commission from links on this page, at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more.
Before you touch the auger
- Ariens: "Stop engine, remove key, wait for moving parts to stop and remove wire from spark plug before leaving operator's position and attempting to maintain or inspect auger." (Ariens manual)
- Briggs & Stratton: "Never clear or unclog the discharge chute with your hands. Fingers can quickly become caught in the impeller. Always use a clean-out tool." (Briggs manual)
- Cub Cadet: "Never use a standard bolt as this may cause injury and damage the snow blower." (Cub Cadet FAQ)
- Honda: "Do not replace shear bolts with ordinary hardware bolts." (Honda manual)
- Snapper: "Do not replace shear pins with anything other than the correct grade replacement shear pin. Use of bolts, screws, or harder grade shear pins can result in equipment damage." (Snapper manual)
Shear pin lookup by brand and model
Pick your brand or type your model number (it’s on a sticker on the frame, usually behind the auger housing or under the dash). Every row comes from the manufacturer’s own parts pages, charts or manuals, with the link. If the source doesn’t give a pin size, we show the part number only. Always confirm in your operator’s manual before you buy.
Ariens
Ariens shear bolts go on the auger (2 per machine). Its manuals give a torque of 5.8 to 12.2 lb-ft but no bolt size, so we show part numbers only. Ariens parts lookup
Deluxe (24, 28, 30, 28 SHO, Track; 2008 and newer incl. ST-series Deluxe)
Models listed by source: 921004, 921005, 921006, 921007, 921008, 921009, 921023, 921024, 921030, 921032, 921035, 921044, 921045, 921046, 921047, 921048, 921069, 921070, 921071, 921072
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Current kit: 3 bolts with nuts. Ariens says it replaces 52100100. | 72100600 (3-pack) | — | Not stated by source | OEM parts page (checked 2026-11-20) · find it |
| Auger Number printed in Deluxe manuals 2008-2024. Ariens now ships 72100600 in its place. | 52100100 (3-pack) | — | Not stated by source | OEM parts page + 5 more (2, 3, 4, 5, 6) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Platinum, Deluxe Platinum and Platinum SHO
Models listed by source: 921028, 921029, 921057, 921063, 921064, 921933
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Current kit for Deluxe, Platinum and Professional. | 72100600 (3-pack) | — | Not stated by source | OEM parts page (checked 2026-11-20) · find it |
| Auger 2013 Deluxe/Deluxe Platinum manual (921028, 921029). | 52100100 | — | Not stated by source | operator's manual (retailer-hosted copy) + 1 more (2) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Professional (Pro 28/32/36, RapidTrak, EFI, hydrostatic)
Models listed by source: 926060, 926068, 926069, 926070
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Current kit for Deluxe, Platinum and Professional. | 72100600 (3-pack) | — | Not stated by source | OEM parts page (checked 2026-11-20) · find it |
| Auger Pro hydrostatic RapidTrak manual (926060, 926069). | 52100100 | — | Not stated by source | operator's manual + 1 more (2) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Pre-2008 Deluxe / Professional (Sno-Thro 924xxx)
Models listed by source: 924116, 924117, 924300, 924505, 924506, 924508
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Ariens: for select pre-2008 Deluxe and Professional models. 3 bolts and 3 nuts. | 51001500 (3-pack) | — | Not stated by source | OEM parts page + 1 more (2) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Compact and Classic (incl. ST compact 932xxx)
Models listed by source: 920013, 920014, 920021, 920022, 920025, 920028, 920029, 920030, 920316, 920317, 920318, 920321, 920325, 920326, 932040, 932041, 932042, 932140, 932141, 932509, 932510, 932511
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Current kit. Ariens says it replaces 53200500. Page names Compact and Classic. | 73203900 (3-pack) | — | Not stated by source | OEM parts page (checked 2026-11-20) · find it |
| Auger Number printed in Compact/Classic manuals. Superseded by 73203900. | 53200500 (3-pack) | — | Not stated by source | OEM parts page + 3 more (2, 3, 4) (checked 2026-11-20) · find it |
| Auger Compact parts manual: 2 per unit on the auger. Nut 06529700 is a .25-20 locking center nut; bolt size not stated. | 53200500 | 06529700 | Not stated by source | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Sno-Tek (20, 20E, 24E)
Models listed by source: 920402, 920406, 939401
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Ariens lists Sno-Tek for 53200500. Its replacement, 73203900, names only Compact and Classic, so confirm with Ariens for Sno-Tek. | 53200500 (3-pack) | — | Not stated by source | OEM parts page + 2 more (2, 3) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Briggs & Stratton
From Briggs & Stratton parts manuals. Snapper and Simplicity manuals we found give the procedure but no pin part numbers.
1227MD dual-stage 27 in (Mfg. No. 1696619-02)
Models listed by source: 1227MD, 1696619-02
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Kit: 2 auger shear bolts and 2 lock nuts. | 707555 (2-pack) | — | Not stated by source | OEM parts manual (retailer-hosted copy) (checked 2026-11-20) · find it |
| Impeller (blower) Kit: 2 impeller screws, 2 flat washers, 2 lock nuts. | 707561 (2-pack) | — | Not stated by source | OEM parts manual (retailer-hosted copy) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
1530MDS dual-stage 30 in (Mfg. No. 1696828-00)
Models listed by source: 1530MDS, 1696828-00
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger | 707555 | — | Not stated by source | OEM parts manual (retailer-hosted copy) (checked 2026-11-20) · find it |
| Impeller (blower) | 707561 | — | Not stated by source | OEM parts manual (retailer-hosted copy) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Craftsman (MTD-built)
Covers MTD-built Craftsman models: 247.xxxxx and CMXGBAM model numbers. Other Craftsman model prefixes aren't covered yet. Craftsman parts
CMXGBAM two-stage (Craftsman by MTD, about 2018 and newer)
Models listed by source: CMXGBAM1054541, CMXGBAM1054542, CMXGBAM1054543, CMXGBAM1054544, CMXGBAM1054546, CMXGBAM…
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger From a third-party copy of the Craftsman manual. Craftsman supplement 769-26036 maps these to MTD models (e.g. CMXGBAM1054541 = 31AS6BEE793). | 738-04124A | — | Not stated by source | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
CMXGBAM1054546 three-stage
Models listed by source: CMXGBAM1054546, 31AH5DTQ793
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger & accelerator (3-stage) sources differ From a third-party copy of the manual; it lists 738-05273 for the side augers and the accelerator. Sources disagree on the 3-stage accelerator pin: 2015-2016 manuals list 738-04124A for every pin, a 2017 manual lists 738-05273 for the side augers and the accelerator, and 2021+ manuals list 738-06654 for the accelerator. Go by the manual for your model and year. | 738-05273 | — | Not stated by source | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Craftsman 247.xxxxx two-stage (MTD-built)
Models listed by source: 247.88845, 247…
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger sources differ Craftsman kit for 247.xxxxx snow blowers; Craftsman says it replaces 738-04155. 6 shear pins and 6 cotter pins. Some 247 models use 738-04124A instead, so check your manual. | CMXGZAM241056 (6-pack) | — | Not stated by source | OEM parts page (checked 2026-11-20) · find it |
| Auger 247.88845 manual (third-party copy). | 738-04155 | — | Not stated by source | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Cub Cadet
MTD-built machines use shear pins held by a bow-tie cotter pin (714-04040), not a bolt and nut. The model number (for example 31AM5HVSB10) is on a label on the frame. Cub Cadet shear pin FAQ
2X two-stage (mid-size frame, 3/4 in auger shaft, 2005 and newer)
Models listed by source: 31AM5HVSB10, 2X 24" HP, 2X 26" HP, 2X 524 WE, 2X 524 SWE, 2X 526 SWE, 2X 528 SWE
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Single pin. Held by bow-tie cotter pin 714-04040. Current Cub Cadet manuals say 738-04124A (round head). | 738-04124A (1-pack) | 714-04040 | .25 × 1.5 in | OEM parts page + 4 more (2, 3, 4, 5) (checked 2026-11-20) · find it |
| Auger 2-pack kit with bow-tie cotter pins; appears to replace 490-241-C063. | 490-241-F071 (2-pack) | — | 1/4 × 1.5 in | OEM parts page (checked 2026-11-20) · find it |
| Auger 4-pack kit with bow-tie cotter pins. | OEM-738-04124 (4-pack) | — | 1/4 × 1.5 in | OEM parts page (checked 2026-11-20) · find it |
| Auger 4-pack kit with bow-tie cotter pins. | 490-241-C063 (4-pack) | — | 1/4 × 1.5 in | OEM parts page (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
3X three-stage
Models listed by source: 31AH7JVXB10
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger sources differ Side augers: black round head pin marked '3'. Sources disagree on the 3-stage accelerator pin: 2015-2016 manuals list 738-04124A for every pin, a 2017 manual lists 738-05273 for the side augers and the accelerator, and 2021+ manuals list 738-06654 for the accelerator. Go by the manual for your model and year. | 738-05273 | 714-04040 | Not stated by source | operator's manual + 1 more (2) (checked 2026-11-20) · find it |
| Accelerator (3-stage) sources differ Central accelerator: hex head pin marked 'A'. Sources disagree on the 3-stage accelerator pin: 2015-2016 manuals list 738-04124A for every pin, a 2017 manual lists 738-05273 for the side augers and the accelerator, and 2021+ manuals list 738-06654 for the accelerator. Go by the manual for your model and year. | 738-06654 (1-pack) | 714-04040 | 0.25 × 1.5 in | operator's manual + 2 more (2, 3) (checked 2026-11-20) · find it |
| Auger & accelerator (3-stage) sources differ The 2015 supplement lists this one pin for 2X and 3X models. Sources disagree on the 3-stage accelerator pin: 2015-2016 manuals list 738-04124A for every pin, a 2017 manual lists 738-05273 for the side augers and the accelerator, and 2021+ manuals list 738-06654 for the accelerator. Go by the manual for your model and year. | 738-04124A | 714-04040 | Not stated by source | operator's manual (checked 2026-11-20) · find it |
| Auger & accelerator (3-stage) sources differ Kit for all Cub Cadet three-stage models: 4 auger pins and 2 accelerator pins, with bow-tie cotter pins. | 490-241-C062 (6-pack) | — | 1/4 × 1.5 in | OEM parts page (checked 2026-11-20) · find it |
| Auger & accelerator (3-stage) Newer 3-stage kit number; the page doesn't list fitment or say how it relates to 490-241-C062. | 753-10904 (6-pack) | — | 1/4 × 1.5 in | OEM parts page (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Large frame two-stage (1 in auger shaft, 2006 and newer), e.g. 930 SWE
Models listed by source: 930 SWE
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger 4-pack with bow-tie cotter pins, for large-frame machines with a 1 in auger shaft (Cub Cadet, Troy-Bilt and MTD). The page's marketing line says 'impeller'; the manuals put this pin on the auger. | OEM-738-04155 (4-pack) | — | 1/4 × 1-3/4 in | OEM parts page (checked 2026-11-20) · find it |
| Auger 930 SWE manual (third-party copy). | 738-04155 | — | Not stated by source | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Three-stage snow thrower attachment for lawn/garden tractors (19A40024100)
Models listed by source: 19A40024100
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Tractor attachment, not a walk-behind. The only MTD source we found that states the grade. | 738-04124A | 714-04040 | .25 × 1.50 in, Grade 2 | operator's manual (retailer-hosted copy) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Honda
Honda HSS machines have shear bolts on both the auger and the blower (impeller). Older HS models: the manuals we found give the procedure but no part numbers.
HSS724A (two-stage, 24 in)
Models listed by source: HSS724A
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger | 90119-V45-A00 | 90343-ZE6-000 | 6 x 18 bolt | operator's manual (checked 2026-11-20) · find it |
| Impeller (blower) | 90121-V45-A00 | 90343-ZE6-000 | 6 x 18 bolt (carriage-type) | operator's manual (checked 2026-11-20) · find it |
| Auger Spare kit: 5 auger shear bolts and 5 nuts, per the manual. | 06766-V45-A00 (5-pack) | — | 6 x 18 mm | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
HSS928A and HSS1332A (two-stage, 28/32 in)
Models listed by source: HSS1332A, HSS928A
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger This manual shows 6 mm self-lock nuts but gives no nut part number. | 90119-V45-A00 | — | 6 x 18 | operator's manual (checked 2026-11-20) · find it |
| Impeller (blower) | 90121-V45-A00 | — | 6 x 18 (carriage type) | operator's manual (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Husqvarna
Husqvarna ST machines have shear pins on the auger and the impeller. Three different part numbers appear in Husqvarna's own sources; match yours by manufacturing ID on the parts list. Husqvarna shear bolts page
ST 224 to ST 430T two-stage (ST 200/300/400)
Models listed by source: ST 224, ST 227, ST 227P, ST 230, ST 324, ST 324P, ST 327, ST 327P, ST 327T, ST 330, ST 330P, ST 330PT, ST 424, ST 424T, ST 427, ST 427T, ST 430, ST 430T
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Not stated sources differ Husqvarna accessory page; fits all 18 models listed. No size, pack count or location. Husqvarna's ST 327P parts lists show different numbers (below). | 580 79 04-01 | — | Not stated by source | OEM parts page (checked 2026-11-20) · find it |
| Auger sources differ ST 224/227/230 manual gives two lengths for the auger pin. No part number. | Not listed | — | 1/4-20 × 2 (replacement step) vs 1/4-20 × 1-3/4 (loose parts list) | operator's manual (checked 2026-11-20) |
| Impeller (blower) ST 224/227/230 manual: the impeller has shear pins too. | Not listed | — | 1/4-20 (length not stated) | operator's manual (checked 2026-11-20) |
| Auger sources differ ST 324/327/330 manual gives two lengths for the auger pin. No part number. | Not listed | — | 1/4-20 × 2 (replacement step) vs 1/4-20 × 1-3/4 (loose parts list) | operator's manual (checked 2026-11-20) |
| Impeller (blower) ST 324/327/330 manual: the impeller has shear pins too. | Not listed | — | 1/4-20 (length not stated) | operator's manual (checked 2026-11-20) |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
ST 327P parts lists by manufacturing ID
Models listed by source: ST 327P, 96193009201, 96191008300, 96191008301, 96191008302, 96193009203, 96191008303
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Not stated sources differ Mfg. ID 96193009201. Listed as 'BOLT SHEAR 1/4-20' in the auger housing/impeller section. Older IDs use 585 51 18-01, later ones 588 07 75-01; the accessory page sells 580 79 04-01. | 585 51 18-01 | 873 80 04-00 | 1/4-20 (length not stated) | OEM parts list + 1 more (2) (checked 2026-11-20) · find it |
| Not stated sources differ Mfg. ID 96191008301. Listed as 'BOLT SHEAR 1/4-20' in the auger housing/impeller section. Older IDs use 585 51 18-01, later ones 588 07 75-01; the accessory page sells 580 79 04-01. | 588 07 75-01 | 873 80 04-00 | 1/4-20 (length not stated) | OEM parts list + 3 more (2, 3, 4) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
MTD / Bolens
MTD-built machines use shear pins held by a bow-tie cotter pin (714-04040), not a bolt and nut.
MTD 300, 500, 600 and 800 Series two-stage (2005 and newer)
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger MTD shear pin retail-pack sheet for 300/500/600 Series two-stage (2005 and after). | 738-04124A | — | Not stated by source | OEM chart (checked 2026-11-20) · find it |
| Auger | 738-04124A | 714-04040 | Not stated by source | operator's manual (retailer-hosted copy) + 2 more (2, 3) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Bolens 930 SWE (large frame)
Models listed by source: 930 SWE
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Third-party copy of the manual. | 738-04155 | — | Not stated by source | operator's manual (checked 2026-11-20) · find it |
| Auger Large-frame (1 in auger shaft) kit. | OEM-738-04155 (4-pack) | — | 1/4 × 1-3/4 in | OEM parts page (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Toro
Toro contradicts itself on shear pins (see below the lookup). None of Toro's manuals we checked mention shear bolts. Toro's product pages name no models, so the model lists come from a parts retailer. Toro parts lookup
Power Max HD (two-stage)
Models listed by source: 38800, 38801, 38802, 38803, 38805, 38820, 38823, 38824, 38826
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger sources differ Current kit; Toro says it replaces 133-2576. The model list above comes from a parts retailer (second source link), not Toro. Toro's help center says its two-stage blowers don't use shear pins, but Toro sells these auger bolt pin kits and says the pins break as designed. | 139-9901 | — | Not stated by source | OEM parts page + 1 more (2) (checked 2026-11-20) · find it |
| Auger Toro installation sheet for the older kit number. | 133-2576 | — | Kit: 2 bolts 5/16 × 2-1/2 in, 2 bolts 1/4 × 2 in, with locknuts and spacers (sheet doesn't say which bolt goes where) | Toro installation sheet (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Power Max (two-stage)
Models listed by source: 37760, 37770, 37771, 37772, 37775, 37777, 37779, 37781, 38810, 38811, 38813, 38815
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger sources differ Toro says 139-9900 replaces 133-2575. No contents or fitment listed; the model list above comes from a parts retailer (second source link). Toro's help center says its two-stage blowers don't use shear pins, but Toro sells these auger bolt pin kits and says the pins break as designed. | 139-9900 | — | Not stated by source | OEM parts page + 1 more (2) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Troy-Bilt
MTD-built machines use shear pins held by a bow-tie cotter pin (714-04040), not a bolt and nut. The model number (for example 31CM6CP3B66) is on a label on the frame. Troy-Bilt parts lookup
Storm two-stage (Storm 2410, 2620, 2840, Storm Tracker 2890; current Storm 2620)
Models listed by source: 31CM6CP3B66, Storm 2410, Storm 2620, Storm 2840, Storm Tracker 2890
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger Round head pin, held by bow-tie cotter pin 714-04040. | 738-04124A | 714-04040 | Not stated by source | operator's manual + 5 more (2, 3, 4, 5, 6) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Vortex three-stage (Vortex 2895 XP; older Vortex Tracker 2890 and Vortex 3090 XP)
Models listed by source: 31AH5EP8B66, Vortex 2895 XP, Vortex Tracker 2890, Vortex 3090 XP
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger sources differ Side augers (current manuals). Sources disagree on the 3-stage accelerator pin: 2015-2016 manuals list 738-04124A for every pin, a 2017 manual lists 738-05273 for the side augers and the accelerator, and 2021+ manuals list 738-06654 for the accelerator. Go by the manual for your model and year. | 738-05273 | 714-04040 | Not stated by source | operator's manual + 1 more (2) (checked 2026-11-20) · find it |
| Accelerator (3-stage) sources differ Central accelerator (current manuals). | 738-06654 | 714-04040 | Not stated by source | operator's manual + 1 more (2) (checked 2026-11-20) · find it |
| Auger & accelerator (3-stage) sources differ Older Vortex Tracker 2890 and Vortex 3090 XP manuals list only 738-04124A, including the rear accelerator pin. Sources disagree on the 3-stage accelerator pin: 2015-2016 manuals list 738-04124A for every pin, a 2017 manual lists 738-05273 for the side augers and the accelerator, and 2021+ manuals list 738-06654 for the accelerator. Go by the manual for your model and year. | 738-04124A | 714-04040 | Not stated by source | operator's manual (retailer-hosted copy) + 1 more (2) (checked 2026-11-20) · find it |
| Auger & accelerator (3-stage) sources differ Troy-Bilt sells the same 3-stage kit: 4 auger and 2 accelerator pins with cotter pins. | 490-241-C062 (6-pack) | — | 1/4 × 1.5 in | OEM parts page (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
Polar Blast 4510 and other large-frame two-stage (1 in auger shaft)
Models listed by source: 4510, Polar Blast 4510
| Location | Shear pin part # | Nut / cotter pin # | Size / grade | Source |
|---|---|---|---|---|
| Auger 4-pack with bow-tie cotter pins. | OEM-738-04155 (4-pack) | — | 1/4 × 1-3/4 in | OEM parts page (checked 2026-11-20) · find it |
| Auger Size and grade come from the troybilt.ca bulk (50-pack) listing for this part. | 738-04155 | — | .25 × 1.75 in, Grade 2 | OEM parts page + 1 more (2) (checked 2026-11-20) · find it |
Confirm the part number in your operator’s manual or on the maker’s parts page for your exact model and serial.
9 brands, 26 series and 57 pin rows, checked 2026-11-20. Part numbers get superseded, so if the maker’s site shows a newer number, use that. “Sources differ” means two official sources list different parts; read the notes and check your manual. Spot an error? Tell us and include the source link.
What a shear pin does, and why a regular bolt is a bad idea
On a two-stage snow blower, the auger (the spiral blades up front) is bolted to the auger shaft with shear pins. When the auger jams on something solid, the pins break first. The auger then freewheels on the shaft instead of forcing the gearbox to take the hit.
That only works if the pin is weaker than the parts it protects. Honda’s manual says it plainly: “Shear bolts are designed to break under force that would otherwise damage auger and blower parts. Do not replace shear bolts with ordinary hardware bolts” (Honda HSS928A/HSS1332A owner’s manual). Snapper warns that “use of a harder grade shear pin will reduce the protection” (Snapper operator’s manual). Ariens adds that if you use a pin that can handle more torque than your machine, “you risk causing extensive damage to your snow blower” (Ariens).
A grade 5 or grade 8 bolt from the hardware store won’t break when it should. The next thing to give is the auger gearbox, and that’s a much bigger repair than a pin.
Signs a shear pin broke
- The auger stops, but the engine and impeller keep going. Snow still blows out the chute from what’s already in the housing, but nothing new gets pulled in.
- One half of the auger turns and the other doesn’t. Most two-stage machines have a pin on each side of the auger, so one can break while the other holds.
- With the engine off and the key out, an auger half spins freely by hand while the shaft stays put. Ariens describes exactly this: broken pins allow the “auger to turn freely on the shaft” (Ariens Sno-Tek manual).
- You hit something right before it happened: the end-of-driveway ice ridge, a buried newspaper, a landscape rock, a dog leash.
If both pins are intact and the auger still won’t turn, the problem is somewhere else, usually the auger drive belt or cable: see snow blower auger not turning for the symptom table and cable checks by brand. Shear bolts on a tractor-mounted blower? See compact tractor snow removal. If the engine itself is the problem, start with our snow blower won’t start guide.
How to replace a snow blower shear pin
What you’ll need: – The correct OEM shear pins and nuts for your model (look it up above). Check for spares first. Honda’s HSS tool kit includes spare shear bolts and self-lock nuts, Husqvarna’s ST manuals list six spare shear pins with locknuts in the loose parts, and on select Cub Cadet and Troy-Bilt models there are holes in the rear of the handle panel for storing spare shear pins and cotter pins (MTD operator’s manual). – A socket or wrench set. Sizes vary by machine, so check your manual. – A hammer and a pin punch to drive out the broken pieces. – Penetrating oil if the old pin is rusted in. – Gloves. Auger edges are sharp.
Steps:
- Shut it all the way down. Stop the engine, wait for all moving parts to stop, remove the key, and pull the spark plug wire. Ariens: “Stop engine, remove key, wait for moving parts to stop and remove wire from spark plug before leaving operator’s position and attempting to maintain or inspect auger” (Ariens service manual).
- Clear the jam with the clean-out tool, not your hand. Honda notes that hand contact with the rotating impeller inside the chute “is the most common cause of injury associated with snow blowers” (Honda HSS724A manual).
- Find the broken pin. Look where each auger half meets the shaft for an empty hole or a stub of bolt. Three-stage machines (Cub Cadet 3X, Troy-Bilt Vortex) also have a pin on the central accelerator behind the auger. Some machines (Honda HSS, Husqvarna ST and some Briggs & Stratton models) have shear bolts on the impeller too. The lookup shows the location where the maker lists it.
- Line up the holes. Rotate the auger half by hand until the hole in the auger tube lines up with the hole in the shaft.
- Drive out what’s left of the old pin with the punch. Spray penetrating oil and give it a few minutes if it’s stuck.
- Insert the new pin and secure it. On Cub Cadet, Troy-Bilt and MTD-built Craftsman machines, the shear pin is held by a bow-tie cotter pin (part 714-04040), not a nut. On Ariens, Honda, Husqvarna and Briggs & Stratton machines it’s a bolt with a nut, often a locking nut. Use the nut or cotter pin that comes with the new pin.
- If it’s a bolt, tighten it, but don’t overdo it. Ariens gives 5.8 to 12.2 lb-ft and says, if you don’t have a torque wrench, to “tighten bolts until they no longer spin freely. DO NOT overtighten” (Ariens Deluxe manual). Use the number in your manual if it gives one.
- Check the other pins for cracks, bends or looseness, then reconnect the spark plug wire and test the auger in an open area.

Why shear pins keep breaking
- You’re hitting things. Gravel driveways, landscape edging and the hard-packed ridge the plow leaves are the usual culprits. Raise the skid shoes so the housing rides a little higher on gravel.
- The pin was the wrong part. A pin that’s too soft or the wrong length can fail under normal load. Use the OEM number for your model.
- The pin was loose, or cranked down too hard. Ariens says overtightening “could stress the shear pin and result in premature failure,” and Briggs & Stratton tells owners to check shear bolts “at frequent intervals for proper tightness” (Briggs & Stratton manual).
- The auger is seizing on the shaft. Simplicity says to lubricate the grease fittings on the auger shaft regularly: “If auger rusts to shaft, damage to worm gear may occur if shear pins do not break” (Simplicity manual). Check your manual for the interval, and do it with the rest of your off-season prep (see fuel stabilizer and carburetor cleaning).
Does Toro use shear pins?
Toro’s answers contradict each other. Its help center says “Toro two-stage snow blowers do not use shear pins,” because the gear case is built to handle the load (Toro). Yet Toro also sells auger bolt pin kits for Power Max and Power Max HD machines. Its own product page says the “auger bolt pins are a weak bolt that connects the auger to the auger shaft” and that “the pins break as designed to protect your auger gearcase” (Toro 139-9901).
What that means for you: if your Toro’s auger stopped and a bolt on the auger is broken, replace it with Toro’s kit (listed in the lookup), not a hardware-store bolt. If the bolts are fine, look at the belt and drive instead.
Part of our snow blower maintenance guide: see the maintenance schedule for your brand, with each maker’s intervals from the manual.
FAQ
Can I use a regular bolt instead of a shear pin? Not even to “get through this storm.” Honda, Snapper, Simplicity and Ariens all say to use only the correct shear pins. A harder bolt moves the breaking point to your gearbox. Keep a few spares in the garage instead.
What size shear pin does my snow blower need? It depends on the machine, so go by part number. Examples from the makers’ own pages and manuals: Cub Cadet’s mid-size two-stage pin (738-04124A) is 1/4 × 1.5 in, and MTD-built large-frame machines with a 1 in auger shaft take 1/4 × 1-3/4 in pins (738-04155). Honda’s HSS724A, HSS928A and HSS1332A use 6 × 18 mm shear bolts. Husqvarna’s ST manuals call for 1/4-20 pins, but give two different lengths. Toro’s Power Max HD kit includes 5/16 × 2-1/2 in and 1/4 × 2 in bolts. If your manual lists a part number, buy that part.
Are snow blower shear pins universal? No. Diameter, length and hardness all vary, and so does the nut or cotter pin. Cub Cadet’s own shear pin chart says “Shear pins are engineered specifically for the model series they’re used on” (Cub Cadet). “Universal” kits are a guess. The OEM part for your model takes the guesswork out.
How many shear pins does a snow blower have? Most two-stage machines have two on the auger, one per side. Ariens manuals list “Shear Bolt (2).” Three-stage machines add pins on the accelerator: Cub Cadet’s three-stage kit holds 4 auger pins and 2 accelerator pins. Some brands, including Honda HSS and Husqvarna ST models, also have shear bolts on the impeller.
Where’s my model number? On a label on the frame, usually at the back of the auger housing, under the control panel, or near the engine. Write it and the serial number on the inside cover of your manual. You’ll need both for parts.
Sources
Every row in the lookup links to its source. Safety and procedure text comes from the manufacturers’ operator’s manuals linked above.
All lookup sources (75)
- Ariens: Shear Bolt Kit (3-Pack) DELUXE PLATINUM PROFESSIONAL – 72100600
- Ariens: Shear Bolt Kit (3-Pack) DELUXE / PLATINUM / PROFESSIONAL – 52100100
- Ariens: Deluxe Series Sno-Thro Operator's Manual 30219300A (9/24)
- Ariens: Deluxe Series Operator's Manual 05135600C (10/19)
- Ariens: Deluxe Series Operator's Manual 04855000D (10/15)
- Ariens: Deluxe Series Sno-Thro Owner/Operator Manual 04754000C (9/14)
- Ariens: Sno-Thro Owner/Operator Manual 03389300 (4/08)
- Ariens: 921 Series Sno-Thro Owner/Operator Manual 04585100A (3/13) – Ariens manual hosted on homedepot-static.com
- Ariens: Platinum Series Operator's Manual 30129700 (7/22)
- Ariens: Professional Series With Hydrostatic Drive Operator's Manual 05136500C (4/18)
- Ariens: Professional Series With Hydrostatic Drive Operator's Manual 05136600C (4/18)
- Ariens: Shear Bolt Kit (3-Pack) Pre-2008 DELUXE / PROFESSIONAL – 51001500
- Ariens: Sno-Thro Owner/Operator Manual 02494100E (4/02)
- Ariens: Shear Bolt Kit (3-Pack) COMPACT CLASSIC – 73203900
- Ariens: Shear Bolt Kit (3-Pack) CLASSIC / COMPACT / SNO-TEK / CROSSOVER – 53200500
- Ariens: Compact Series Operator's Manual 09363300 (7/20) – Ariens manual hosted on pdf.lowes.com
- Ariens: Compact Series Sno-Thro Owner/Operator Manual 04631900B (4/14) – Ariens manual hosted on pdf.lowes.com
- Ariens: Sno-Thro Owner/Operator Manual 00429300B (7/05)
- Ariens: Compact Parts Manual 04632000 (8/13)
- Ariens: Sno-Tek Operator's Manual 05137300A (7/17) – Ariens manual hosted on homedepot-static.com
- Ariens: Sno-Tek Owner/Operator Manual 04334300A (10/11)
- Briggs & Stratton: Briggs & Stratton Parts Manual, Mfg. No. 1696619-02, 1227MD, B&S 11.5 Gross TP 27" Dual (28-Nov-2017)
- Briggs & Stratton: Briggs & Stratton Parts Manual, Mfg. No. 1696828-00, 1530MDS, B&S 11.5 Gross TP 30" (02-Oct-2017)
- Craftsman (MTD-built): Craftsman CMXGBAM1054541 manual, page 27 'Replacing Shear Pins' (manualslib.mx, third-party host)
- Craftsman (MTD-built): Craftsman Shear Pins CMXGZAM241056 (craftsman.com)
- Craftsman (MTD-built): Craftsman 247.88845 Manual, p.15 (manualsonline, third-party host)
- Cub Cadet: Shear Pin, .25" x 1.5" – Item 738-04124A (cubcadet.com)
- Cub Cadet: Operator's Manual Form No. 769-26795 (April 20, 2023), Snow Blower 2-Stage and 3-Stage (500, 600 & 800 Series)
- Cub Cadet: Cub Cadet Snow Blower Models Parts/Warranty Supplement, Form No. 769-26938 (December 13, 2023)
- Cub Cadet: Cub Cadet Parts/Warranty Supplement, Form No. 769-10811 (May 20, 2015)
- Cub Cadet: Cub Cadet (Canada) Parts/Warranty Supplement, Form No. 769-11756A (May 26, 2017)
- Cub Cadet: Shear Pin Kit, .25 x 1.5" – Item 490-241-F071 (cubcadet.com)
- Cub Cadet: Shear Pin Kit, .25 x 1.5" – Item OEM-738-04124 (cubcadet.com)
- Cub Cadet: Shear Pins for Two Stage Snow Blowers – Item 490-241-C063 (cubcadet.com)
- Cub Cadet: Operator's Manual Form No. 769-26797 (April 23, 2023), Snow Blower 2-Stage and 3-Stage (700 Series)
- Cub Cadet: Shear Pin for 3X snow blower accelerators (.25 x 1.5) – Item 738-06654 (cubcadet.com)
- Cub Cadet: SHEAR-PINS 3X – Item 490-241-C062 (cubcadet.com)
- Cub Cadet: Shear Pin Kit for Three Stage Snow Blowers – Item 753-10904 (cubcadet.com)
- Cub Cadet: Shear Pin Kit, .25 x 1.75" – Item OEM-738-04155 (troybilt.com)
- Cub Cadet: Cub Cadet 930 SWE Manual, p.14 (manualsonline, third-party host)
- Cub Cadet: Cub Cadet Operator's Manual Form No. 769-10052D (March 25, 2015), Three-Stage Snow Thrower Attachment — 19A40024100 [Home Depot-hosted]
- Honda: Honda Owner's Manual, Snow Blower HSS724A (00X31V45 A089)
- Honda: Honda Owner's Manual, Snow Blower HSS928A / HSS1332A (00X31V45 A130)
- Husqvarna: Husqvarna Snow Thrower Shear Bolts | Husqvarna US
- Husqvarna: Husqvarna Operator's manual ST 224, ST 227, ST 230
- Husqvarna: Husqvarna Operator's manual ST 324, ST 327, ST 330
- Husqvarna: Husqvarna Illustrated Parts List 586 83 69-27 Rev. 1, ST 327P, Product No. 961 93 00-92, Mfg. ID 96193009201
- Husqvarna: Husqvarna Illustrated Parts List 586 92 10-27 Rev. 2, ST 327P, Product No. 961 91 00-83, Mfg. ID 96191008300
- Husqvarna: Husqvarna Illustrated Parts List 588 13 44-11, ST 327P, Product No. 961 91 00-83, Mfg. ID 96191008301
- Husqvarna: Husqvarna Illustrated Parts List 588 13 44-51, ST 327P, Product No. 961 91 00-83, Mfg. ID 96191008302
- Husqvarna: Husqvarna Illustrated Parts List 588 13 35-88, ST 327P, Product No. 961 93 00-92, Mfg. ID 96193009203
- Husqvarna: Husqvarna Illustrated Parts List 588 13 44-90, ST 327P, Product No. 961 91 00-83, Mfg. ID 96191008303
- MTD / Bolens: MTD 'SHEAR PINS Part # 738-04124(A)' instruction sheet [Home Depot-hosted]
- MTD / Bolens: MTD Operator's Manual Form No. 769-09706 (April 19, 2014), Two-Stage Snow Thrower — 300 Series [Lowe's-hosted]
- MTD / Bolens: Operator's Manual Form No. 769-11510C (May 17, 2017)
- MTD / Bolens: Operator's Manual Form No. 769-11510B (August 18, 2016)
- MTD / Bolens: Bolens 930 SWE Manual, p.14 (manualsonline, third-party host)
- Toro: Snow Blower Auger Pin Bolt Kit | Toro
- Toro: Toro Snowblower Shear Pins – ProPartsDirect
- Toro: Form No. 3408-329 Rev A, Auger Bolt Pin Kit, Power Max® Heavy Duty Snowthrower, Model No. 133-2576, Installation Instructions
- Toro: Power Max Auger Bolt Pins Kit | Toro
- Troy-Bilt: Troy-Bilt Operator's Manual Form No. 769-08981 (June 7, 2013), Two-Stage Snow Thrower — Storm 2410, 2620 & 2840
- Troy-Bilt: Troy-Bilt Operator's Manual Form No. 769-09967, Two-Stage Snow Thrower — Storm Tracker 2890 [Home Depot-hosted]
- Troy-Bilt: Troy-Bilt Snow Blower Models supplement, Form No. 769-26939 (December 13, 2023)
- Troy-Bilt: Troy-Bilt Registration, Parts and Warranty Supplement, Form No. 769-26035 (April 19, 2021) [Home Depot-hosted copy]
- Troy-Bilt: Operator's Manual Form No. 769-26072 (April 20, 2021), Snow Blower 2-Stage and 3-Stage (500, 600 & 800 Series)
- Troy-Bilt: Troy-Bilt Operator's Manual Form No. 769-10857, Three-Stage Snow Thrower — Vortex Tracker 2890 [Lowe's-hosted]
- Troy-Bilt: Troy-Bilt Operator's Manual Form No. 769-09904, Three Stage Snow Thrower — Vortex 3090 XP [Lowe's-hosted]
- Troy-Bilt: Troy-Bilt 490-241-C062 shear pins
- Troy-Bilt: Shear Pin – Qty 50 .25 x 1.75 Gr2 – Item 738-04155-50 (troybilt.ca)
- Troy-Bilt: Troy-Bilt 4510 Manual, p.15 (manualsonline, third-party host)
- Ariens: Ariens service manual
- Briggs & Stratton: Briggs & Stratton operator's manual
- Cub Cadet: Cub Cadet shear pins FAQ
- Snapper: Snapper operator's manual
More winter fixes: snow blower won’t start · snow blower carburetor cleaning · tractor tire chain size finder



