Chart of what Toro, Ariens, Husqvarna, EGO, Honda, Cub Cadet and Troy-Bilt manuals say about using a snow blower on gravel, with skid shoe settings

Snow Blower on a Gravel Driveway: Skid Shoe Settings

Quick answer: Use a two-stage snow blower with its skid shoes lowered, which raises the auger housing and scraper bar above the stone. Toro, Ariens, Husqvarna and EGO all give a gravel setting in their manuals. Ariens, for example, sets the skid shoes on 7/8-inch (22 mm) spacers for gravel. A single-stage blower is the wrong tool: its auger paddles touch the ground, and Toro says its Power Clear “is not designed for removing materials other than snow, nor is it designed for clearing gravel surfaces.” Some two-stage makers go further. Honda’s HSS724A manual says never to use it on a gravel driveway, and Cub Cadet and Troy-Bilt say they don’t recommend it.

Chart of what Toro, Ariens, Husqvarna, EGO, Honda, Cub Cadet and Troy-Bilt manuals say about using a snow blower on gravel, with skid shoe settings

The short version: skid shoes down means housing up. Set it high, leave a thin layer of snow on the stone, and point the chute away from people, cars and windows. Stop the engine, take the key out and pull the spark plug wire before you touch the skid shoes.

What each maker’s manual says about gravel

Every row comes from that maker’s own operator’s manual (linked, with the page). Settings differ by model and year, so check the manual for your model number. Craftsman and PowerSmart aren’t here because we couldn’t find a maker-hosted manual to cite.

Two-stage snow blowers

Machine (manual)Gravel allowed?Gravel settingSkid shoes
Toro Power Max 824 OE (manual, p. 10, 19)Yes, with “extreme caution”Adjust the skids “further down to prevent the machine from picking up rocks.” On pavement the scraper sits 1/8 in (3 mm) upReversible: when worn, turn them over
Ariens Deluxe 24, model 921069 (manual, p. EN-5, EN-17)Yes. Adjust the housing height to clear gravelSkid shoes set on 7/8 in (22 mm) spacers under the scraper blade. Hard, smooth surfaces: 1/8 in (3 mm)Adjustable. Ariens lists a composite skid shoe kit, 72603100 (p. EN-25)
Husqvarna ST 224 (manual, p. 7, 14)Yes. “Adjust the auger housing height to clear gravel or crushed rock surface” (p. 7)Raise the skid plates until the scraper bar is “above the top of the gravel.” Asphalt: 0.2 to 0.25 in (5 to 6 mm)Adjustable with a 13 mm wrench. The scraper bar is reversible
EGO SNT2800, battery (manual, p. 6, 33-34)Only once it’s “adjusted for such a surface”Raise the skid shoes for uneven or gravel surfaces. No figure givenReversible: a steel side and a plastic side
Honda HSS724A (manual, p. 6, 16-17)No. “Never use the snow blower to clear snow from a gravel road or driveway”For rough or uneven surfaces its chart gives 1 to 1-3/16 in (25 to 30 mm) of auger clearanceTurn them upside down when worn. Replace below 0.02 in (0.5 mm)
Cub Cadet 524 to 530 WE/SWE (manual 769-08161, p. 10, 12)Not recommended: it “can easily pick up and throw loose gravel”If you do, keep the skid shoes “in position for maximum clearance between the ground and the shave plate” (on most machines that means the lowest shoe setting; that reading is ours)Adjustable, four nuts
Troy-Bilt Storm 2410, 2620, 2840 (manual 769-08981, p. 11, 17)Not recommended (same wording)Maximum clearance, same as Cub CadetDeluxe shoes have two wear edges. Rotate them 180°

Two notes on the table:

  • Honda’s two answers. Its safety section says never to clear a gravel driveway, but its clearance chart still lists a rough-surface setting. If you own a Honda and have gravel, read that as “it’s at your own risk, and set it at least that high.”
  • Ariens’ own blog says less. A November 2026 Ariens article suggests 1/2-inch spacers for gravel. The Deluxe manual says 7/8 inch. Start with your manual, and go higher if you still pick up stone.

Single-stage snow blowers

A single-stage blower has no skid shoes to raise. Its rubber-edged auger runs on the ground and helps pull the machine forward, which is exactly what you don’t want on stone.

Machine (manual)Gravel allowed?What the manual saysHeight adjustment
Toro Power Clear 721 R/E (manual, p. 1, 6)No“Not designed for clearing gravel surfaces”None. Its housing-height warning is for “two-stage models only”
Ariens Path-Pro SS21 (manual, p. EN-12)Avoid stone“Do not pick up gravel and rocks. Push down slightly on handlebar to avoid picking up debris”None
Troy-Bilt Squall 210 / 2100 (manual 769-07131, p. 10, 13)CautionThe rubber paddles “come in contact with the pavement” to propel the machineShave plate only. Wheels, shave plate and auger all touch the ground

Tractor-mounted blowers follow the same rule. Land Pride says gravel needs a higher skid shoe setting than asphalt, and never so low that it picks up rock. Our tractor guide covers PTO blower skid shoes for Land Pride, Woods and Kubota.

How to adjust snow blower skid shoes for gravel

Skid shoes are the two runners bolted to the sides (or rear) of the auger housing. They set how far the scraper bar rides above the ground. Lowering the shoes raises the housing. This is the procedure the manuals above share:

  1. Shut it down. Stop the engine, wait for everything to stop moving, and remove the key (Toro). Honda also says to disconnect the spark plug cap before skid shoe work, so the engine can’t start while you’re near the auger.
  2. Check tire pressure first (Toro). Uneven tires tilt the housing.
  3. Park on a hard, flat surface like the garage floor, not the gravel.
  4. Set the height with spacers. Ariens’ method is the easiest: put a spacer under each end of the scraper blade, 7/8 inch (22 mm) thick for gravel. A scrap of wood cut to that thickness works.
  5. Loosen the skid shoe nuts (two to three per side) and slide each shoe down until it sits flat on the floor. MTD’s manuals say the whole bottom of the shoe should touch, or it wears unevenly.
  6. Set both sides equally, then tighten the nuts securely. Honda says to raise and lower the housing afterward and check that both shoes touch at the same time.
  7. Recheck after you adjust the scraper bar. Ariens says to always adjust the skid shoes after the scraper blade. Toro adds that bumping the machine on the pavement to clear a clog can knock the skids out of position.

If the shoes are worn on one side, check whether yours flip before you buy new ones. Toro’s and Honda’s turn over, Troy-Bilt’s Deluxe shoes rotate 180°, and EGO’s have a steel side and a plastic side. When you do replace them, the Cub Cadet and Troy-Bilt manuals say to use the maker’s original parts.

How to snow blow a gravel driveway without throwing rocks

  • Leave a base layer. Setting the scraper 7/8 inch to 1 inch up means that much snow stays on the drive. That layer is what keeps the auger off the stone. Utah State University Extension says to set the blades “an inch or more above the gravel.”
  • Walk the drive first. Before you start, Honda says to remove “any visible stones, sticks, newspapers, nails, pieces of wire” first. Toro adds doormats, sleds and boards.
  • Aim the chute away from people, cars and windows. MTD’s manuals say to plan your pattern “to avoid discharge towards windows, walls, cars etc.” Toro says never direct it “toward people or areas where property damage can occur.” Husqvarna and Ariens add throwing snow downwind when you can.
  • Keep kids, pets and helpers out of the throw zone. A rock leaves the chute much farther than the snow does (see below).
  • If you hear stone, stop. Raise the housing more. On a single-stage blower, Ariens says to push down slightly on the handlebar so the auger lifts.
  • After a hit, shut it off and inspect it. Toro, Ariens and Husqvarna all say to stop the engine after striking a foreign object and check for damage before restarting. A rock jammed in the auger usually snaps a shear pin first. Our shear pin lookup finds the right part, and auger not turning walks through the other causes.

Safety: thrown rocks and your hands

  • Thrown objects travel far. Utah State University Extension says snow blowers can throw snow more than 20 feet, and “solid objects, such as rocks or ice chunks, can travel three times that distance.” Toro’s manual warns the impeller “can throw stones, toys, and other foreign objects and cause serious personal injury to you or bystanders.”
  • Wear eye protection. Toro says to wear it while operating and while making adjustments.
  • Engine off, key out, spark plug wire off before you adjust skid shoes or reach near the auger. Ariens says to remove the wire from the spark plug after hitting something, and Honda says to disconnect the spark plug cap before skid shoe work.
  • Never clear a clog by hand. The CPSC counted over 4,200 snow blower injuries treated in emergency rooms in 2021, with over 40 percent to the wrist, hand and finger. It says to use a cleanout tool or a long stick, “NOT your hands.” Honda warns that a jammed auger can move suddenly when the clog breaks free.

If your blower won’t start after sitting since last winter, start with how to start a snow blower, then the won’t start guide.

Part of our snow blower maintenance guide: see the maintenance schedule for your brand, with each maker’s intervals from the manual.

FAQ

Can you use a snow blower on a gravel driveway? Yes, with a two-stage blower set high. Toro, Ariens, Husqvarna and EGO give a gravel setting in their manuals: lower the skid shoes so the scraper bar rides above the stone. Honda’s HSS724A manual says never to clear a gravel driveway, and Cub Cadet and Troy-Bilt don’t recommend it, so check yours.

Can a single-stage snow blower be used on gravel? Not safely. Single-stage augers run on the ground. Toro says its Power Clear “is not designed for removing materials other than snow, nor is it designed for clearing gravel surfaces,” and Troy-Bilt’s Squall manual says the rubber paddles contact the pavement to pull the machine forward. On a gravel drive, use a two-stage blower or a shovel.

How high should skid shoes be for gravel? High enough that the scraper bar clears the stone. Ariens uses 7/8-inch (22 mm) spacers. Honda’s chart gives 1 to 1-3/16 inches (25 to 30 mm) for rough or uneven ground, and Utah State University Extension says an inch or more. Husqvarna just says to get the scraper bar above the top of the gravel.

Do you raise or lower skid shoes for gravel? Lower them. The shoes slide down on the housing, which lifts the housing and scraper bar off the ground. Toro’s manual puts it as “adjust the skids further down to prevent the machine from picking up rocks.”

Can you flip snow blower skid shoes? Many, yes. Toro’s and Honda’s skid shoes turn over when one side is worn. Troy-Bilt’s Deluxe shoes rotate 180° to a second wear edge. EGO’s have a steel side and a plastic side you can swap for different surfaces.

Sources

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top