Quick answer: Every spring, or every 25 to 50 hours, change the oil, clean or replace the air filter, check or replace the spark plug, start on fresh gas, sharpen the blade and clean under the deck. Riding mowers add the battery terminals, tire pressure, grease fittings and belts. Before each mow, check the oil. In the fall, stabilize or drain the gas. The makers set different intervals: Briggs & Stratton push engines replace the plug every year, Honda GCV every 2 years or 200 hours, Kohler 7000 every 500 hours. Find your engine below.
Jump to the table: How often: the short version ↓
YardGuides may earn a commission from links on this page, at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more.

Find your engine: Briggs push · Briggs V-twin · Honda · MTD (Cub Cadet, Troy-Bilt, Craftsman) · Kohler · Kawasaki · Riding mower chassis · Spark plug table · Air filter table
The maker and model are on the engine’s label, not the mower’s. Our oil guide shows where to find your engine label.
Safety first, every time. Stop the engine, let it cool, and pull the spark plug wire or cap before you touch the blade or anything under the deck (Briggs, p. 8; Honda GCV, p. 9). On electric-start riders, Briggs also says to disconnect the negative battery cable (p. 8).
Every interval on this page is printed in the maker’s own manual, linked with the page. Where a manual says nothing, we say “not listed.” Where the makers disagree, we show both. Anything that’s our own reasoning is labeled.
How often: the short version
| Task | Most manuals say | Exceptions |
|---|---|---|
| Check engine oil | Before each use | Briggs: every 8 h or daily. Kawasaki: daily |
| First oil change | After the first 5 hours | Honda: first month or 5 h. Toro TimeCutter: 8 h. None listed: Kohler, Kawasaki, John Deere. None at all on Briggs engines labeled “Just Check & Add” or “No Oil Changes” |
| Regular oil change | Every 50 hours or yearly | Honda: 6 months or 50 h, 25 h under heavy load or heat. Kohler, Kawasaki, Toro TimeCutter: 100 h. Briggs V-twin with a yellow or orange filter: 100 h or yearly. Cub Cadet XT’s mower manual says 50 h for its Kohler and Kawasaki engines. Our take: use the shorter interval |
| Air filter | Clean every 25 h, replace yearly | Honda GCV: replace every 2 years or 200 h. Kawasaki: clean the paper every 100 h. John Deere: replace yearly or 50 h, never clean the paper |
| Spark plug | Replace yearly | Honda GCV: 2 years or 200 h. Kohler: 500 h. Kawasaki: clean and regap every 100 h. Husqvarna YTH: each season or 100 h, whichever comes first. Toro TimeCutter: service every 100 h, replace it if it has a black coating, worn electrodes, an oily film or cracks |
| Fuel filter | Replace yearly | MTD: yearly or 100 h. Kohler 7000: 100 h. Honda: clean the tank and filter yearly or 100 h, a dealer job unless you’re mechanically proficient. Briggs push manual: not listed |
| Blade | Sharpen or replace yearly | John Deere: yearly or 50 h. Husqvarna YTH: check every 25 h. Cub Cadet XT: every 10 h. Honda HRN: inspect before each use |
| Deck | Clean after each use, level yearly | John Deere: level yearly or 50 h. Cub Cadet XT: 25 h. Husqvarna YTH: 50 h |
| Riders: grease, tires, battery | Every 25 h | John Deere grease: first 8 h, then 25 h. Tires and battery terminals: Cub Cadet every 10 h, John Deere yearly or 50 h (terminals) |
| Valves | A dealer, only on some engines | Briggs: annual check “not required unless engine performance problems are noted.” Honda: yearly or 100 h. John Deere, Kohler Courage: 200 h. Kawasaki: 300 h. Kohler 7000: 500 h |
Oil grades and amounts are in our lawn mower oil guide. Gas and stabilizer rules are in does fuel stabilizer work?
Hours or seasons?
Honda and John Deere say to use whichever comes first, the hours or the calendar (Honda GCV, p. 9; John Deere, p. 28). Push mowers have no hour meter, so our suggestion is to go by the calendar column. Briggs says “a typical walk-behind lawn mower is used 20 to 25 hours per year” (80107981, p. 12), so for most push mowers “every 25 hours” means about once a year. Riding mowers usually have an hour meter. Cub Cadet owners: here’s how to read the Cub Cadet hour meter.
Maintenance schedule by engine maker
Briggs & Stratton push mower engines
From the Briggs & Stratton operator’s manual 80098074 for the 080000, 090000, 093J00 and 100000 engines (p. 8).
| Task | When | What the manual says (page) |
|---|---|---|
| Check engine oil | Every 8 h or daily | (p. 8) |
| First oil change | After 5 h | Not required on models labeled Just Check & Add or No Oil Changes (p. 8) |
| Change engine oil | Every 50 h or annually | Same exception. Grade and amount: oil guide (p. 8) |
| Muffler area, controls, air intake grille | Every 8 h or daily | Clean (p. 8) |
| Air filter and pre-cleaner | Clean every 25 h or annually, replace annually | More often in dust. See the air filter table (pp. 8 to 9) |
| Spark plug | Replace annually | Gap and part number: plug table (pp. 8 to 10) |
| Cooling system | Annually | A Briggs dealer cleans the cylinder fins, which needs partial disassembly (pp. 8 to 9) |
| Valve clearance | Annually | “Not required unless engine performance problems are noted” (p. 8) |
| Fuel filter | Not listed in the manual |
“Just Check & Add” means no oil changes. Briggs says an oil change is not required on these engines, only topping up (p. 8). Toro’s 22in Recycler manual also makes the yearly change optional: “Change the engine oil (if desired)” (p. 21). The other makers here list one.
Briggs & Stratton V-twin (riding mowers)
From the Briggs operator’s manual 80107981 for the 400000, 440000 and 490000 V-twins (pp. 7 to 8). It’s a different manual from the push engines, and the intervals differ.
| Task | When | What the manual says (page) |
|---|---|---|
| Check engine oil | Every 8 h or daily | (pp. 7 to 8) |
| First oil change | After 5 h | Only on engines without an oil filter (pp. 7 to 8) |
| Oil and filter | 50 h or annually, or 100 h or annually | 50 h with no filter or the standard black filter. 100 h with the yellow or orange high-efficiency filter (p. 8). Filter numbers: oil guide |
| Air filter and pre-cleaner | Clean every 25 h or annually, replace annually | (p. 8) |
| Spark plug | Replace annually | (p. 8, parts p. 10) |
| Fuel filter | Replace annually | Part 84001895. Drain the tank or close the fuel valve first (pp. 8 to 10) |
| Exhaust system | Every 50 h or annually | Service it (p. 8) |
| Cooling system | Annually | Dealer cleans the cylinder fins (pp. 8 to 9) |
| Valve clearance | Annually | “Not required unless engine performance problems occur” (p. 8) |
Briggs says it recommends an authorized dealer “for all maintenance and servicing” on both engine families (80098074, p. 8; 80107981, pp. 7 and 10). Briggs also says not to adjust the carburetor or engine speed (80098074, p. 8; 80107981, p. 8).
Honda GCV170, GCV200 (Honda HRN mowers)
From the Honda GCV170 and GCV200 engine owner’s manual (00X37Z9V0001, p. 9). Honda says to go by months or hours, “whichever comes first.”
| Task | When | What the manual says (page) |
|---|---|---|
| Oil level and air filter | Before each use | Check (p. 9) |
| First oil change | First month or 5 h | (p. 9) |
| Change engine oil | Every 6 months or 50 h | Every 25 h under heavy load or in high heat (p. 9) |
| Air filter | Clean every 3 months or 25 h, and at 6 months or 50 h. Replace every 2 years or 200 h | Paper element (pp. 9 to 10) |
| Flywheel (blade) brake | Every 6 months or 50 h | The engine should stop quickly when you let go of the lever. Under 2 mm (0.08 in) of lever clearance goes to a dealer (pp. 9, 11) |
| Spark plug | Check yearly or 100 h, replace every 2 years or 200 h | (pp. 9 to 11) |
| Spark arrester (if fitted) | Yearly or 100 h | Clean (pp. 9, 11) |
| Idle speed, fuel tank and filter, valve clearance | Yearly or 100 h | A Honda dealer, unless you have the tools and are “mechanically proficient” (p. 9) |
| Fuel lines | Every 2 years | Check, replace if needed. Same dealer note (p. 9) |
Honda’s mower manual differs from its engine manual. The HRN216 mower manual (00X31VR8B004, p. 11) replaces the plug and air filter every 150 hours or 2 years, not 200 hours, and lists a yearly flywheel brake pad check, a dealer job unless you have the tools and are mechanically proficient. It also has you inspect the blades, blade bolts and blade control before each use. Our take: when the mower and engine manuals differ, use the shorter interval.
MTD engines (Cub Cadet, Troy-Bilt, Craftsman push mowers)
From the MTD 79cc, 132cc and 140cc vertical shaft engine manual (769-25030, p. 9). MTD says to follow the hourly or calendar interval as listed.
| Task | When | What the manual says (page) |
|---|---|---|
| Check engine oil | Each use or every 5 h | (p. 9) |
| First oil change | After 5 h | (p. 9) |
| Change engine oil | Every season or 50 h | Every season or 25 h under heavy load or high temperature (p. 9) |
| Air filter | Check each use or 5 h, service every season or 100 h | Paper: “cannot be cleaned,” replace once a year or every 100 h (pp. 9 to 10) |
| Spark plug | Check every season or 25 h, replace every season or 100 h | (pp. 9, 11) |
| Engine shroud, muffler area | Each use or every 5 h | Clean (p. 9) |
| Fuel filter | Every season or 100 h | Part 951-12296. It “cannot be cleaned” (pp. 9, 11, 14) |
Craftsman owners: Craftsman mowers have used engines from several makers. Read the engine label and use that maker’s table.
Kohler (riding mowers)
From the Kohler 7000 Series (KT610 to KT745) owner’s manual (32 590 31, p. 5).
| Task | When | What the manual says (page) |
|---|---|---|
| Precleaner | Every 25 h | Service or replace (p. 5) |
| Air cleaner element | Every 25 to 100 h | Depends on the air cleaner type and whether it has a precleaner (p. 5) |
| Oil and oil filter | Every 100 h | (p. 5) |
| Cooling shrouds and fins | Every 100 h | Remove the shrouds and clean (p. 5) |
| Fuel filter | Every 100 h | Replace (p. 5) |
| Fasteners | Every 100 h | Check they’re in place and secure (p. 5) |
| Spark plug | Every 500 h | Replace and set the gap (p. 5) |
| Valve lash | Every 500 h | Kohler dealer (p. 5) |
Kohler Courage SV470 to SV620 (20 590 06, p. 5) puts most items on “100 hours or annually,” checks valve lash at 200 h (dealer), and replaces the plug at 500 h. Kohler Command PRO (24 590 54, p. 5) changes oil every 100 h or yearly and the oil filter and fuel filter every 200 h. It allows 300 h for oil and filter only with Kohler PRO 10W-50 oil and a Kohler PRO filter. Smart-Choke trouble on a 7000? See Kohler 7000 Smart-Choke problems.
Kawasaki FR and FS (riding mowers)
From the Kawasaki FR651V, FR691V and FR730V owner’s manual (99920-2289-03, pp. 23 to 24). Kawasaki calls its intervals a guide and says to service more often in hard conditions.
| Task | When | What the manual says (page) |
|---|---|---|
| Oil, leaks, fasteners, air inlet screen | Daily | Check (p. 23) |
| Engine oil | Every 100 h or 1 year | (p. 24) |
| Oil filter | Every 200 h | (p. 24) |
| Air cleaner paper element | Clean every 100 h, replace yearly or 200 h | (pp. 24, 28) |
| Spark plugs | Every 100 h | Clean and regap (pp. 24, 29) |
| Cylinder and head fins | Every 100 h | Dealer or “equally qualified service facility” (p. 24) |
| Valve clearance, combustion chamber, valve seats | Every 300 h | Dealer (p. 24) |
| Fuel filter | When clogged | No interval printed. It can’t be taken apart, so replace it (p. 30) |
The Kawasaki FS481V to FS600V manual (99920-2294-04, p. 31) adds a foam element that gets cleaned every 25 hours. FX-series owners: see our Kawasaki FX1000V guide.
Riding mower and lawn tractor chassis
The engine manual covers the engine. The grease points, deck, belts and tires are in the mower’s own manual.
| Machine | Lube points and interval | Deck and belts | Tire pressure (page) |
|---|---|---|---|
| John Deere S100 to S180 | Spindles, front axle pivot and wheel bushings: first 8 h, then every 25 h. John Deere Multi-Purpose HD Lithium Complex Grease or Grease-Gard Premium Plus (p. 28) | Yearly or 50 h: sharpen or replace blades, check belts, check and level the deck, clean the deck (p. 28) | S100, S110, S120, S130, S140, S160: 14 psi front, 10 psi rear. S170, S180: 12 psi front and rear (p. 49) |
| Husqvarna YTH18542 | Lube chart every 25 h and before storage, general purpose grease (p. 14) | Blades every 25 h, deck level every 50 h, V-belts every 100 h (p. 14) | The psi on the tire sidewall. Check before each use (pp. 14 to 15) |
| Cub Cadet XT1, XT2 | All grease points every 25 h and before storage, No. 2 multi-purpose grease (pp. 21, 23 to 24) | Blades and deck cleaning every 10 h, deck level every 25 h, belts every 50 h (p. 21) | The tire sidewall. Check every 10 h (pp. 13, 21) |
| Toro TimeCutter 5000 | Caster wheel bearings every 25 h, No. 2 lithium grease (pp. 29 to 30) | Clean the deck after each use, belts every 25 h (p. 29) | Casters 30 psi (206 kPa), drive tires 13 psi (90 kPa) (p. 38) |
| Zero-turn transaxles | Check the transaxle maker’s manual for its oil interval (our advice; the engine manuals here don’t cover it) | Zero-turn won’t start with the blades or levers set wrong? See the zero-turn safety switch guide | Your mower manual or tire sidewall |
John Deere says to check tire pressure “with an accurate low-pressure gauge” (p. 43), and that the pressure “is also located on the sidewalls of the tires” (p. 49). Its S-series transmission needs nothing: “The transmission is a sealed component. No maintenance is required” (p. 35). Deck belt routing for the John Deere 54-inch deck: John Deere 54″ deck belt diagram.
Spark plug: type, gap and when to replace
Use the plug and gap your engine manual prints. The gap isn’t the same on every mower, even inside one Briggs manual.
| Engine | Plug the manual names | Gap | Replace, and torque (page) |
|---|---|---|---|
| Briggs & Stratton 080000, 090000, 093J00 (push) | Briggs resistor plug 692051 | 0.020 in (0.51 mm) | Annually. 180 lb-in (20 Nm) (80098074, pp. 8 to 10) |
| Briggs & Stratton 100000 (163 cc) | Briggs resistor plug 594056 | 0.030 in (0.76 mm) | Annually. 180 lb-in (20 Nm) (pp. 8, 10) |
| Briggs & Stratton V-twin 400000, 440000, 490000 | Briggs resistor 491055S or Long Life Platinum 5066K | .030 in (.76 mm) | Annually. 180 lb-in (80107981, pp. 8, 10) |
| Honda GCV170, GCV200 and HRN216 | NGK BPR5ES (BPR6ES on pressure washers) | 0.028 to 0.031 in (0.7 to 0.8 mm) | Every 2 years or 200 h (HRN216 manual: 150 h). New plug 1/2 turn after it seats, reused 1/8 to 1/4 turn (GCV pp. 9 to 11, 13) |
| MTD 79, 132 and 140 cc vertical shaft | MTD 951-10292 (79 cc) or 951-14437 (132, 140 cc) | 0.030 in (0.76 mm) | Every season or 100 h. New plug 1/2 turn, reused 1/8 to 1/4 turn (pp. 9, 11, 14) |
| Kohler 7000 (KT610 to KT745) | Not printed in the owner’s manual | 0.030 in (0.76 mm) | Every 500 h. 20 ft. lb. (27 N·m) (pp. 5, 7, 8) |
| Kohler Courage SV470 to SV620 | Not printed in the owner’s manual | 0.03 in (0.76 mm) | Every 500 h. 20 ft. lb. (27 N·m) (pp. 5, 7, 8) |
| Kawasaki FR651V, FR691V, FR730V | NGK BPR4ES | 0.030 in (0.75 mm) | Clean and regap every 100 h. 22 N·m (16 ft·lb) (pp. 12, 24, 29) |
| Kawasaki FS481V, FS541V, FS600V | NGK BPR4ES | 0.030 in (0.75 mm) | Clean and regap every 100 h. 22 N·m (16 ft·lb) (pp. 14, 32) |
| John Deere S100 to S180 (Briggs engines) | Not printed in the manual | 0.030 in (0.76 mm) | Yearly or 50 h. 15 lb-ft (20 N·m) (pp. 28, 34) |
| Husqvarna YTH18542 | Champion XC92YC | .030 in (0.76 mm) | Every 100 h and each season. 180 lb-in (20 Nm) (pp. 4, 14, 17) |
| Toro TimeCutter 5000 | NGK BPR4ES | 0.03 in (0.75 mm) | Every 100 h (pp. 29, 34) |
Two printing quirks, so you’re not confused. Honda’s step-by-step text prints the gap as 0.028 to 0.030 in (GCV, p. 11), while its spec table prints 0.028 to 0.031 in (p. 13). Our reading: set it between 0.028 and 0.030 in and you’re inside both. The Briggs V-twin manual prints the torque as “180 lb-in (180 Nm)” (p. 10). 180 lb-in is about 20 N·m (our conversion), which matches the 180 lb-in (20 Nm) in the Briggs push-engine manual, so we read “180 Nm” as a misprint.
Free printable: seasonal maintenance checklist for your mower & tractor
A 2-page spring-to-winter checklist for riding and push mowers and compact tractors. Then short, practical emails a couple of times a month. Unsubscribe anytime.
How long does a spark plug last? From one season (Briggs, John Deere) to 2 years or 200 hours (Honda GCV) to 500 hours (Kohler). Kawasaki has you clean and regap it every 100 hours rather than replace it on a timer.
How to check, gap and replace a lawn mower spark plug
- Engine cool, plug wire or cap off. Clean around the plug so dirt can’t fall in (Honda, p. 11; Kohler, p. 7).
- Inspect it. Honda: replace it “if damaged, badly fouled, if the sealing washer … is in poor condition, or if the electrode is worn” (p. 11). MTD: discard it if the insulator is cracked or chipped (p. 11).
- Gap it with a wire gauge, bending only the side electrode (Briggs, p. 8; Kawasaki, p. 29). Briggs: “Do not change the gap on platinum, iridium or twin tip spark plugs, as the fine electrodes may get damaged” (Briggs spark plug FAQ).
- Thread it in by hand so it doesn’t cross-thread (Honda, p. 11; MTD, p. 11).
- Tighten it to the torque in the table, or on Honda and MTD engines, 1/2 turn past seated for a new plug and 1/8 to 1/4 turn for a reused one.
Clean it or not? The makers split. MTD lets you wire-brush a plug you’re reusing (p. 11), and Kawasaki and John Deere have you clean it with a wire brush (Kawasaki, p. 29; John Deere, p. 34). Toro’s TimeCutter manual says “Do not clean the spark plug(s)” and to replace one with a black coating, worn electrodes, an oily film or cracks (p. 34). Its own schedule (p. 29) says “Replace or clean and gap the spark plug,” so the manual contradicts itself. Our reading: follow p. 34 and replace it.
Use the plug your manual names. Honda: “Incorrect spark plugs can cause engine damage” (p. 11), and Briggs says the wrong plug can cause “performance problems and possible internal engine damage.” Any equivalents above are the makers’ own words. We don’t cross-reference other plug brands.
How to tell if a lawn mower spark plug is bad
Replace it when the manual’s criteria say so: worn or pitted electrodes, a cracked or chipped insulator, heavy fouling or a black coating, or a bad sealing washer (Honda, p. 11; MTD, p. 11; John Deere, p. 34; Toro TimeCutter, p. 34). If the plug looks fine and the engine still won’t fire, that’s a no-start problem: work through lawn mower won’t start.
Air filter: clean, oil or replace?
Whether you oil the foam depends on two things: your engine maker, and whether the foam is the main filter or a precleaner sitting over a paper element. The manual for your engine decides.
| Engine and filter | When (page) | Oil the foam? | Compressed air on the paper? |
|---|---|---|---|
| Briggs push, foam filter | Clean every 25 h or annually, replace annually (p. 8) | Yes. “Soak the foam element … with clean engine oil,” then squeeze out the excess (p. 9) | No paper. No pressurized air or solvents on any filter (p. 9) |
| Briggs push, paper with pre-cleaner | Same (p. 8) | No. “Do not add oil to the pre-cleaner” (p. 9) | No. “Do not use pressurized air or solvents to clean the filter” (p. 9) |
| Briggs V-twin, paper with pre-cleaner | Clean every 25 h or annually, replace annually (p. 8) | No. “DO NOT lubricate the pre-cleaner” (p. 9) | No (p. 9) |
| Honda GCV, paper | Check each use, clean at 3 months or 25 h, replace every 2 years or 200 h (p. 9) | No foam in this manual | Yes, under 30 psi (207 kPa), blown from the engine side (p. 10) |
| MTD 79 to 140 cc, foam (primer engines) | Service every season or 100 h (p. 9) | Yes. “OIL the foam element with a light engine oil” (p. 10) | No paper |
| MTD 79 to 140 cc, paper (auto-choke engines) | Replace once a year or every 100 h (p. 10) | No foam | Not addressed. MTD says paper “cannot be cleaned” (p. 10) |
| Kohler 7000, paper with precleaner | Precleaner every 25 h, element every 25 to 100 h by type (p. 5) | Yes. “Lightly oil precleaner with new engine oil” (p. 7) | No. “Paper element cannot be blown out with compressed air” (p. 7) |
| Kohler Courage, paper with precleaner | Precleaner every 25 h or annually (p. 5) | Yes. “Saturate precleaner with new engine oil” (p. 7) | No (p. 7) |
| Kawasaki FR, paper | Clean every 100 h, replace yearly or 200 h (p. 28) | No foam. “Do not oil paper element” (p. 28) | No (p. 28) |
| Kawasaki FS, foam over paper | Foam every 25 h, paper every 100 h (pp. 31 to 32) | No. “Do not oil foam or paper element” (p. 32) | No (p. 32) |
| John Deere S100 to S180, paper (foam precleaner on S160 to S180) | Replace yearly or 50 h (p. 28) | No. “Do not use oil” (p. 33) | No. “Do not use pressurized air to clean element” (pp. 32 to 33) |
Where they disagree, in short: Briggs, MTD and Kohler oil their foam. Briggs (on a pre-cleaner), Kawasaki and John Deere say no oil. Honda allows low-pressure air through a paper filter. Briggs, Kohler, Kawasaki and John Deere say no.
How to clean a lawn mower air filter
- Foam: wash it in liquid detergent and water. Squeeze it, don’t twist it: MTD says twisting “could damage or tear the foam element” (p. 10). Let it dry, then oil it only if your manual says to (table above) and squeeze out the excess.
- Paper: tap it on a hard surface to knock the dirt loose, or replace it if it’s dirty (Briggs, p. 9; Kawasaki, p. 28). Honda says never brush it, because that forces dirt into the fibers (p. 10). John Deere says not to tap it either, just replace it when it’s very dirty or damaged (pp. 32 to 33).
- Never run it without the filter. MTD: “Never run the engine without the air filter. Rapid engine wear will result” (p. 10). Briggs says the same (p. 9).
Filter soaked with oil? That usually comes from overfilling or tipping the mower the wrong way. See too much oil (or oil in the air filter), and Briggs’ tipping warning in lawn mower won’t start.
Fuel filter: where it is and how often
| Engine or mower | Filter and interval | Notes (page) |
|---|---|---|
| Briggs push engines | Not listed in the manual | (80098074, p. 8) |
| Briggs V-twin | In-line, replace annually | Part 84001895, an original filter (80107981, pp. 8 to 10) |
| Honda GCV | Fuel tank and filter, clean yearly or 100 h | Dealer item unless you’re mechanically proficient (p. 9) |
| MTD 79 to 140 cc | In the tank outlet, replace yearly or 100 h | Part 951-12296. More often if run on old gas (pp. 11, 14) |
| Kohler 7000, Courage | Replace every 100 h | Command PRO: every 200 h (p. 5) |
| Kawasaki FR | Replace when clogged | No interval printed (p. 30) |
| John Deere S100 to S180 | In-line, yearly or 50 h | Change it when the fuel is low (pp. 28, 34) |
| Husqvarna YTH18542 | In-line, once each season | (pp. 14, 17) |
| Toro TimeCutter, Cub Cadet XT | In-line, 100 h (Toro) or 50 h (Cub Cadet) | (Toro p. 29; Cub Cadet p. 21) |
Swapping an in-line filter in 3 steps (Briggs V-twin, p. 9; John Deere, p. 34):
- Stop the fuel. Close the fuel shut-off valve or drain the tank. John Deere says to change it when the fuel is low.
- Move the clamps back with pliers and pull the lines off. Check the lines for cracks while they’re off.
- Fit the new filter with the arrow pointing toward the engine, put the clamps back, and check for leaks.
If fuel isn’t reaching the carburetor at all, or a rider dies after a few minutes, see riding mower carburetors.
Spring tune-up checklist
What a lawn mower tune-up includes
- Battery (riders): charge it and clean the terminals. See the riding mower battery guide.
- Fresh gas: drain old gas if it sat untreated. See does fuel stabilizer work?
- Oil: change it if it’s due and check the level. See the lawn mower oil guide.
- Air filter: clean or replace it per the air filter table.
- Spark plug: check the gap or replace it per the plug table.
- Blade: sharpen, balance and install it the right way up. See correct blade position and balancing blades with star holes.
- Deck: clean it and check that it’s level (below).
- Tires (riders): set them to your manual’s psi in the chassis table.
- Grease (riders): hit every fitting in the chassis table.
- Belts: look for cracks and wear. John Deere 54-inch deck: belt routing diagram.
- Interlocks and blade brake: Toro says the engine must stop “within 3 seconds after releasing the blade-control bar” (Recycler, p. 21). Honda has you check the flywheel brake (GCV, p. 11). Riders: zero-turn safety switch and the 5-pole ignition switch diagram.
- Test start outdoors: the steps differ by engine. See first start by engine maker.
- If it won’t start, go to lawn mower won’t start. If it surges, see why is my lawn mower surging? Toro Recycler 22 owners: Recycler 22 won’t start.
The order is our suggestion: the battery and gas first, so the mower is ready for the test start at the end.
Deck: clean it and check it’s level
- Plug wire off first. John Deere has you disconnect the spark plug wires or the negative battery cable before any deck work (p. 18).
- Clean it. Toro’s Recycler and TimeCutter manuals have you clean under the deck after each use (Recycler p. 21; TimeCutter p. 29). John Deere decks with a wash port get a one-minute flush after each use, with the blades running and the engine at full throttle (pp. 24 to 25). Husqvarna doesn’t recommend a hose or pressure washer on the tractor except at the washout port, unless the engine and transmission are covered (p. 17).
- Level it yearly or every 50 hours (John Deere, p. 28). Set the tires to pressure first. John Deere sets the front of the deck 1/8 to 1/4 in (3 to 6 mm) lower than the rear (pp. 18 to 20).
Poor bagging or a ragged cut after a clean deck? See how to improve lawn mower suction.
End of season
- Fuel: stabilize it or drain it, depending on your engine maker. The rules are in stabilize or drain? What each engine maker says.
- Oil: Briggs, Kohler, John Deere and Husqvarna change it before storage. Kawasaki’s FR manual changes it after (Briggs 80098074 p. 9, 80107981 p. 10; Kohler p. 7; John Deere p. 48; Husqvarna p. 14; Kawasaki FR p. 32).
- Battery (riders): charge it and keep it from freezing. See storing it for winter.
- The full fall routine: how to winterize a lawn mower.
DIY or dealer?
| Engine or mower | The manual sends to a dealer (page) | The manual has you do it (page) |
|---|---|---|
| Briggs push and V-twin | Carburetor and engine speed adjustments, cylinder fin cleaning. Briggs recommends a dealer “for all maintenance and servicing” (80098074, pp. 8 to 9; 80107981, pp. 7 to 9) | Oil, air filter, plug and, on V-twins, the fuel filter (pp. 8 to 9) |
| Honda GCV | Idle speed, fuel tank and filter, valve clearance, fuel lines, unless you’re mechanically proficient. Flywheel brake with under 2 mm of lever clearance (pp. 9, 11) | Oil, air filter, plug, spark arrester (pp. 9 to 11) |
| MTD 79 to 140 cc | No dealer items in the schedule. “Do not modify engine in any way” (p. 3) | Everything in its schedule (pp. 9 to 11) |
| Kohler 7000 and Courage | Valve lash (500 h on the 7000, 200 h on the Courage), and anything needing “special timing or adjustment procedures” (pp. 5, 8). Kohler also recommends “a Kohler authorized dealer for all maintenance, service, and engine parts” (p. 7) | Oil and filter, air cleaner, fuel filter, plug (pp. 5 to 7) |
| Kawasaki FR | Fin cleaning, valve clearance, combustion chamber, valve seats (p. 24) | Oil and filter, air cleaner, plugs (pp. 24 to 29) |
| John Deere S100 to S180 | Valve clearance every 200 h (p. 28) | Everything else in its schedule (p. 28) |
Carburetor work by maker is in what each engine maker lets you do. Governor and choke problems: Briggs V-twin governor and Kohler 7000 Smart-Choke. Electrical faults on Simplicity tractors: Simplicity electrical problems.
What you’ll need
- A spark plug socket and the plug your manual names. Search by that part number and match it to your manual
- A wire-type spark plug gap gauge. Briggs, Kohler and John Deere all call for a wire gauge
- A torque wrench that reads in the range your plug torque falls in
- The air filter and fuel filter by the part numbers in your manual. Lawn mower air filters, searched by engine model
- Riders: a grease gun with the grease your mower manual names, and a low-pressure tire gauge. John Deere asks for “an accurate low-pressure gauge”
- Oil and a drain pan: see the oil guide. Battery charger: see the battery guide
FAQ
How often should a lawn mower be serviced? Once a year for most homeowners, usually in spring, plus an oil check before every mow. Most engine manuals give hours too, usually every 25 to 50 hours, and say to go by whichever comes first. Honda asks for an oil change every 6 months or 50 hours, and Kohler and Kawasaki riding mower engines every 100 hours (Cub Cadet’s XT manual says 50 hours on those same engines; our take: use the shorter interval). Find your engine’s table above.
What does a lawn mower tune-up include? Fresh gas, an oil change, a clean or new air filter, a checked or new spark plug, a sharp blade and a clean deck. Riding mowers add the battery, tire pressure, grease fittings and belts. Finish with an interlock check and a test start outdoors. The spring tune-up checklist links each step to its guide.
How often should you change a lawn mower spark plug? It depends on the engine. Briggs & Stratton push engines and John Deere S-series tractors: yearly. Honda GCV: every 2 years or 200 hours. Husqvarna YTH: every season or 100 hours, whichever comes first. Toro TimeCutter: check it every 100 hours and replace it when it’s worn or fouled. Kohler 7000 and Courage: every 500 hours. Kawasaki says to clean and regap it every 100 hours.
What is the spark plug gap on a lawn mower? There’s no single number. Small Briggs & Stratton push engines (080000, 090000, 093J00) use 0.020 in. Honda GCV engines use 0.028 to 0.031 in. MTD, Kohler, Kawasaki, the Briggs 100000 and Briggs V-twins use 0.030 in. Check the plug table for yours.
Should I oil a foam air filter? Only if your manual says so. Briggs (foam main filter), MTD and Kohler say to oil the foam. Briggs says not to oil a pre-cleaner that sits on a paper filter, and Kawasaki and John Deere say no oil at all. The air filter table lists each one.
Do push mowers need maintenance? Yes. A push mower’s engine needs the same oil, air filter, spark plug and fuel care as a rider’s, plus a sharp blade and a clean deck. It skips the grease fittings and tire pressure, and the battery unless it has electric start (Toro’s Recycler charges it every 25 hours, p. 21). At 20 to 25 hours a year (Briggs’ figure), most push mowers hit their intervals once a season.
What maintenance does a riding mower need that a push mower doesn’t? Grease fittings (usually every 25 hours), tire pressure, belts, deck leveling and the battery. Many riding mower engines also have an oil filter. The chassis table has John Deere, Husqvarna, Cub Cadet and Toro intervals.
Can I tip my mower to clean under the deck? Only the way your engine manual says, because the makers disagree on which side goes up. Check which side up, by engine maker before you tip it. On a battery mower there’s no oil or gas to worry about. Its blade and storage care are in winterizing a battery mower.
Sources
- Briggs & Stratton, Operator’s Manual 80098074 Rev B, 080000, 090000, 093J00, 100000: maintenance schedule and plug p. 8; air filter, cooling and specifications p. 9; specifications and parts p. 10. Copy hosted by Toro
- Briggs & Stratton, Operator’s Manual 80107981 Rev A, 400000, 440000, 490000 V-twin: maintenance schedule pp. 7 to 8; air filter, fuel filter and cooling p. 9; specifications and parts p. 10; hours per year p. 12
- Briggs & Stratton, What is the right spark plug and gap for my small engine? (updated April 6, 2026)
- Honda, GCV170 / GCV200 Owner’s Manual 00X37Z9V0001: maintenance schedule p. 9; air filter and required plug p. 10; plug service and flywheel brake p. 11; specifications p. 13
- Honda, HRN216 Lawn Mower Owner’s Manual 00X31VR8B004: maintenance schedule p. 11
- MTD, 79cc, 132cc and 140cc Engine Operator’s Manual 769-25030: do not modify p. 3; maintenance schedule p. 9; air filter p. 10; spark plug and fuel filter p. 11; replacement parts p. 14
- Kohler, 7000 Series KT610-KT745 Owner’s Manual 32 590 31: maintenance schedule p. 5; spark plug and air cleaner p. 7; specifications and troubleshooting p. 8
- Kohler, Courage SV470-SV620 Owner’s Manual 20 590 06: maintenance schedule p. 5; spark plug and air cleaner p. 7; specifications p. 8
- Kohler, Command PRO CH/CV620-750 Owner’s Manual 24 590 54: maintenance schedule p. 5
- Kawasaki, FR651V / FR691V / FR730V Owner’s Manual 99920-2289-03: tune-up specifications p. 12; maintenance chart pp. 23 to 24; air cleaner p. 28; spark plug p. 29; fuel filter p. 30
- Kawasaki, FS481V / FS541V / FS600V Owner’s Manual 99920-2294-04: tune-up specifications p. 14; air cleaner and spark plug pp. 31 to 32
- John Deere, S100 to S180 Lawn Tractors Operator’s Manual OMUC22642: deck leveling pp. 18 to 20; wash port pp. 24 to 25; service intervals and lubrication p. 28; air cleaner pp. 32 to 33; spark plug and fuel filter p. 34; transmission p. 35; tires pp. 43, 49. Retailer-hosted copy (Lowe’s)
- Husqvarna, YTH18542 Operator’s Manual 114 25 66-32: specifications p. 4; maintenance schedule p. 14; tires p. 15; spark plug, fuel filter and cleaning p. 17
- Cub Cadet, XT1 and XT2 Enduro Series Operator’s Manual 769-10976: tires p. 13; maintenance schedule p. 21; lubrication pp. 23 to 24
- Toro, TimeCutter 5000 Operator’s Manual 3466-168: maintenance schedule p. 29; greasing p. 30; spark plug p. 34; tires p. 38
- Toro, 22in Recycler Operator’s Manual 3441-821: maintenance schedule p. 21
Related guides: Lawn mower won’t start · Lawn mower oil · Carburetor cleaning · Riding mower battery · Does fuel stabilizer work? · How to winterize a lawn mower · Same engines, winter side: snow blower maintenance



