Chart comparing compact tractor snow tools: loader bucket, clamp-on plow, rear and front blades, rear 3-point and front mid-PTO snowblowers

Plowing Snow With a Tractor: Blade, Blower or Bucket?

Quick answer: For light, frequent snow, the loader bucket or a rear blade is enough. For moderate snow on a short driveway, a front or rear blade moves it faster. For deep or drifting snow, long driveways, or nowhere to pile it, use a PTO snowblower, sized to the horsepower range its maker prints. Rear 3-point blowers run off the 540 rpm rear PTO. Front blowers need a mid-PTO (Deere calls it a front PTO) and a front hitch. Whatever you pick, set up ballast and traction first.

Chart comparing compact tractor snow tools: loader bucket, clamp-on plow, rear and front blades, rear 3-point and front mid-PTO snowblowers

YardGuides may earn a commission from links on this page, at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more.

Every width, horsepower range and ballast figure below comes from the maker’s own spec sheet or operator’s manual, and each row links to it. We haven’t tested these attachments. Makers update models and specs, so the manual for your serial number and your dealer have the final say.

Which snow tool fits your driveway?

Start with how much snow you get per storm, how long your driveway is, and where the snow can go.

ToolSnow it handles wellDriveway it suitsWhat your tractor needs
Loader bucketLight, frequent snowShort drives with room to pileA loader, rear ballast
Clamp-on bucket plowLight to moderate snowShort to medium drivesA loader, rear ballast
Loader snow pusherModerate snow, pushed straightWide, open paved areasA loader with a quick-attach plate, rear ballast
Front angle bladeModerate snowMedium drives with banks along the sidesFront hitch, a hydraulic outlet for angling
Rear bladeLight to moderate snowShort to medium drives3-point hitch, front weight or a loader
Rear 3-point blowerDeep or drifting snowLong drives, no room to pileRear 540 rpm PTO in the blower’s hp range
Front mid-PTO blowerDeep or drifting snowLong drives, no room to pileMid-PTO, a front hitch, rear counterweight

The surface matters too:

SurfaceBlade or bucketSnowblower
Asphalt or concreteBucket level in float; a rubber edge is an option on some blades (Kubota sells one for its BX blade)Skid shoes can sit lower
GravelFloat, and raise the edge slightly (or use skid shoes) so you don’t scrape up stoneLand Pride says gravel needs a higher skid shoe setting, and never so low that it picks up rock

Blades and buckets push snow, so you need somewhere to put it. After a few storms the banks get tall and the drive gets narrower. A blower throws snow past the edge, which is why it’s the answer for deep snow and long drives. It’s also the most expensive and the most maintenance.

Snow attachment requirements by maker

This is the table we couldn’t find anywhere else: each maker’s own width and horsepower figures side by side. Two warnings before you use it:

  • Read the hp column carefully. Deere and Woods state PTO hp. Land Pride and Bercomac rate rear blowers by tractor hp. Bercomac rates its big front blowers by engine hp. Your tractor’s spec sheet lists both engine hp and PTO hp. PTO hp is the lower number.
  • A blank means the maker doesn’t publish it. We didn’t fill gaps with forum numbers.

Rear 3-point snowblowers (540 rpm rear PTO)

Blower (source)WidthMaker’s hp rangeHitch
Deere Frontier SB114848 in16–35 PTO hpCat. 1
Deere Frontier SB115454 in20–40 PTO hpCat. 1
Deere Frontier SB116464 in20–50 PTO hpCat. 1
Deere Frontier SB117474 in35–50 PTO hpCat. 1 and Cat. 2
Deere Frontier SB1184 / SB119484 / 94 in40–80 PTO hp
Woods SB54S54 inUp to 25 PTO hpLimited Cat. 1 and Cat. 1
Woods SB64S64 in15–35 PTO hpLimited Cat. 1 and Cat. 1
Woods SB74C74 in30–50 PTO hpCat. 1 and Cat. 2
Woods SB84C84 in35–60 PTO hpCat. 1 and Cat. 2
Land Pride SB105151 in18–32 tractor hpCat. 1
Land Pride SB106464 in18–59 hp in the spec table, but 18–32 hp under Tractor Requirements (p. 8), which says tractors outside the range “must not be used”; ask a dealerCat. 1
Land Pride SB157474 in30–59 tractor hpCat. 1
Land Pride SB258484 in43–105 tractor hpCat. 1 and Cat. 2
Bercomac 64 in rear64 in18–40 tractor hpCat. 1
Bercomac 72 in rear72 in25–40 tractor hpCat. 1
Bobcat 3-point blower50, 60, 66, 74 inNot published (“select the model appropriate for your tractor PTO horsepower”)Cat. 1

What the rear-blower manuals say about ballast and setup:

  • Land Pride: “Tractors outside the horsepower range must not be used.” PTO speed is 540 rpm. Hydraulic chute rotation and tilt (optional) each need a duplex hydraulic outlet. “Ballast weights may be required to maintain steering control” (SB10/15/25 manual 370-027M, Tractor Requirements, p. 8).
  • Woods: a minimum of 20% of the tractor and equipment weight must stay on the front wheels in transport. Woods also says to set the rear wheels narrower than the blower’s cutting width (MAN0869, p. 11). A loader on the front usually covers the front weight.
  • Bercomac: 540 rpm PTO, and counterweights may be needed to keep control of the tractor (rear blower manual 110361, p. 8).

Land Pride’s chart is from its manual for older serial numbers (S/N 881640 and lower), and Land Pride’s own Application paragraph in that manual says 30 to 105 hp. The newer manual (370-430M) may list different figures, so confirm with a dealer.

Front-mount snowblowers (mid-PTO or front PTO)

Blower (source)WidthFits / maker’s hp rangeMount and drive
Deere 47 in heavy-duty blower47 inDeere shows it on a 1025R; no fit list or hp range on the pageFront 3-point hitch, 2,000 rpm front PTO, hydraulic lift and spout
Deere 54 in heavy-duty blower54 inNo fit list or hp range on the pageFront 3-point hitch, hydraulic spout
Kubota BX2830 blower48 inBX1880, BX2380, BX2680, BX23SBX2810 front quick hitch, BX2811 mid-PTO driveline (mid PTO 2,500 rpm per the BX Series brochure, p. 13), loader valve for lift and chute
Kubota BX2822A blower55 inBX series, not the BX1880Same as BX2830
Bercomac 72 in front blower72 in40–55 engine hpMid-PTO (shaft “turns up to 2000 RPM”)
Bercomac 80 in front blower80 in48–65 engine hpMid-PTO
Bobcat front-mount blower49, 62, 72 in modelsNot publishedFront mount; height and chute run “from the loader control valve”

Kubota’s BX blower manual requires a 350 lb rear counterweight. More on ballast below.

Snow blades

Blade (source)WidthFits / maker’s hp rangeMount
Deere 60 in Quick-Hitch front blade60 inX700 and “select compact tractors”Hydraulic lift with float, optional hydraulic angle
Deere Frontier RB2060 / RB2072 / RB2084 rear blades60 / 72 / 84 in19–45 / 23–55 / 27–55 PTO hpRear 3-point Cat. 1, manual angle, tilt and offset
Kubota BX2812A blade60 inBX seriesBX2810 hitch and BX2417A loader valve, hydraulic angle
Kubota LX2960A / LX2972A blades60 / 72 inLX seriesHydraulic angle; “Mid PTO is not required”
Land Pride RBT15 rear blades60, 72, 84 in17–40 hpRear 3-point, Cat. 1

Check your tractor’s manual too, not just the blower’s. Kubota’s BX23S manual caps a front snowblower at 50 in wide and 353 lb and says a sub frame is necessary (BX23S operator’s manual, implement limits table). Kubota’s brochure lists the 55 in BX2822A for BX tractors other than the BX1880, so if you own a BX23S, ask your dealer which limit applies to your serial number.

How to size a snowblower to your tractor

  1. Find your PTO hp. It’s on your tractor’s spec sheet and in the operator’s manual. Use PTO hp, not engine hp, unless the blower maker says otherwise (see the hp column above).
  2. Check the PTO. Rear blowers in this table all run at 540 rpm. Land Pride says to make sure a multi-speed PTO is set to 540. Front blowers need a mid-PTO. Kubota’s BX mid-PTO runs at 2,500 rpm, Deere lists 2,000 rpm for its 47 in front blower, and Bercomac’s front driveline turns up to 2,000 rpm.
  3. Pick a width inside the maker’s range. Land Pride says flatly that tractors outside the range must not be used.
  4. Cover your tires. Woods says to set the rear wheels narrower than the cutting width, so the blower clears a path for the tires. A blower narrower than your tractor leaves tire tracks of packed snow.
  5. Check the hitch and the lift. Category 1 vs Category 2 has to match, and your 3-point hitch has to lift the blower’s weight. Woods lists its SB64S at 436 lb and SB84C at 632 lb.

The “5 hp per foot” rule of thumb. On TractorByNet, owners often size blowers at about 5 PTO hp per foot of width (so 20 hp for a 48 in blower). Others call it “just a suggestion” and note that with a hydrostatic transmission you just slow down in heavy, wet snow. Compare it to the makers’ ranges: Deere rates its 48 in SB1148 from 16 PTO hp, Woods rates a 64 in blower at 15 to 35 PTO hp, and Land Pride rates a 51 in blower from 18 tractor hp. The makers’ ranges are wider than the forum rule, and they are the ones to follow.

Free printable: seasonal maintenance checklist for your mower & tractor

A 2-page spring-to-winter checklist for riding and push mowers and compact tractors. Then short, practical emails a couple of times a month. Unsubscribe anytime.

How to plow snow with a tractor loader bucket

Kubota’s loader manual gives the clearest guidance. From the BX23S / LA340 operator’s manual (p. 99):

  • Keep the bucket level and use float. On hard surfaces, “keep the bucket level and put the lift control in the float position.” Kubota says float “will reduce the chance of surface gouging while removing snow.”
  • Don’t push down on it. With hydraulic down pressure, “the bucket will wear faster than normal.”
  • Don’t bulldoze with the bucket dumped. Kubota warns that pushing with the bucket in the dumped position puts “severe shock loads on the dump-linkage, the bucket cylinders, and the tractor” (pp. 101–102). Push with the bucket level and the cutting edge forward.
  • Back-drag to clean up. Kubota allows back grading with “the heel of the bucket.” That’s how you pull snow away from a garage door before you push it.
  • Carry the load low. Ohio State University Extension says to keep loader buckets “as low as possible when moving” (OSU fact sheet). A full bucket of wet snow held high on an icy slope is how tractors tip.

A clamp-on bucket plow bolts or clamps a blade onto the bucket’s cutting edge, so you get a wider, angled push without a front hitch. Match it to your bucket width and the maker’s stated bucket fit. Browse clamp-on bucket snow plows.

A loader snow pusher (a box with side wings on a quick-attach plate) carries more snow straight ahead without spilling. It’s best for wide paved areas, not narrow winding drives.

Rear blade, front blade or bucket: technique

  • Rear blade: You push snow while backing up, or angle the blade and drag it forward to roll snow to one side. Land Pride calls its RBT blades “excellent for snow.” Backing up means you spend most of the job looking over your shoulder, so slow down and know where everyone is.
  • Front blade: Angle it so snow rolls toward the side you’re piling on. Kubota’s BX blade offers skid shoes and a rubber edge as options, which help on gravel or pavers.
  • Bucket: Level, in float, as above. Push the pile back past the edge of the drive early in the season, before the banks get tall.

Traction and ballast: set up before the first storm

Snow work combines everything that makes a tractor lose traction or tip: a heavy load on one end, ice, and slopes. Kubota’s B2301/B2601 manual says to make sure the tractor “is correctly ballasted to avoid skidding and loss of steering control” on icy surfaces, and to engage front wheel drive. Here’s what the attachment manuals say:

SetupMaker’s ballast requirement
Kubota BX2830 / BX2822A front blower“a rear counterweight of 350 lbs.” (manual, p. 20)
Kubota LA340 loader on a BX23S“add rear ballast to the 3-point hitch and to the rear wheels when using the loader.” The amount “will depend on the application” (manual)
Kubota LA525 loader (L2501, L3301, L3901)“rear ballast must be added to the 3-point hitch and to the rear wheels when using loader” (manual, p. 8)
John Deere 1023E / 1025R tractor“Add enough ballast to maintain steering control and prevent tip over” (operator’s manual, p. 27; dealer-hosted copy)
John Deere, any loaderRule of thumb: about a 50/50 rear/front weight split for loader work, and “see your attachment operator’s manual for ballasting requirements” (Deere ballasting safety page)
Land Pride rear blowers“Ballast weights may be required to maintain steering control” (370-027M, p. 8)
Woods rear blowersAt least 20% of the tractor and equipment weight on the front wheels in transport (MAN0869, p. 11)

Notice what’s missing: neither Kubota loader manual gives one fixed weight for loader work. They say it depends on the job. The BX23S manual also says not to use rear wheel weights and liquid ballast at the same time.

Your options for rear weight:

  • Liquid-filled rear tires. Our liquid ballast guide and calculator shows how much weight your tire size holds and which fluids won’t freeze.
  • A ballast box on the 3-point hitch. You fill it with sand, gravel or concrete. It comes off for summer. Browse 3-point ballast boxes.
  • Wheel weights that bolt to the rims, if your maker offers them.

A rear 3-point blower is heavy too, so with a rear blower and a front loader you’re often balanced. With a front blower or blade and nothing on the back, you need the counterweight.

Then traction:

Shear bolts, skid shoes and gearbox oil on tractor-mounted blowers

Shear bolts

Every blower in our table protects its driveline with a shear bolt. It’s meant to break before something expensive does.

BlowerWhat the manual specifies
Kubota BX2830 / BX2822A“grade 2 shearbolt (70060-04465) on fan” and “special grade 5 grooved shear bolts (70060-01338) on the auger sections.” After one breaks, reposition the augers 180° from each other (manual, p. 25)
Deere Frontier SB1148Drive shaft 1/4″ NC x 1 3/4″ Grade 5; driveline M6 x 40 mm grade 8.8 (2009 manual, p. 29; check the current parts list)
Land Pride SB10/15/25Driveline shear bolt M8 x 50 (SB10/15) or M10 x 60 (SB25); auger drive shaft 1/4″-20 Grade 5 (370-027M spec table, p. 35)
Woods SB seriesAuger drive 1/4 NC x 1 in Grade 5; driveline bolt size and grade by driveline maker in the parts list (MAN0869, pp. 18–20)
Bobcat 3-point“A shear bolt through the input shaft protects the gearbox and driveline” (Bobcat)
Bercomac“Use only original shear bolts” (110845 manual, p. 26)

Never swap in a harder bolt. Woods warns that “using a hardened bolt or shear pin may result in damage to driveline or gearbox,” and that fasteners must be replaced “with the same grade as specified in the manual parts list.” Keep a few spares of the exact part number in the tractor. If one keeps breaking, Woods’ troubleshooting chart says to check whether the bolt is the right (not too soft) grade, and to keep the PTO shaft angle under 15 degrees.

Got a walk-behind blower too? Our snow blower shear pin lookup finds the part number by brand.

Skid shoes

Skid shoes set how close the housing rides to the ground.

  • Gravel: Land Pride says gravel or crushed rock needs “a higher setting than hard flat surfaces such as asphalt and concrete. Never set Snow Blower so low as to pick-up gravel and rock.” It also says never to run gravel through the blower.
  • Tilt: Woods says you can set depth with the skid shoes or by tilting the blower, but “excessive forward or backward tilt may cause U-joint to flutter resulting in PTO shear bolt failure.”
  • Kubota BX2830 / BX2822A: skid shoes are adjustable and replaceable, with 3 positions.
  • Walk-behind blower on gravel? See skid shoe settings by brand.

Gearbox oil

  • Land Pride: check with the blower level and the oil cold. Remove the level plug; oil should reach the bottom of the hole. It specifies 80-90W EP gear lube.
  • Woods: check quarterly and keep it half full (level hole halfway up the back of the gearbox). Change it after the first 30 hours or 30 days. Capacity is 0.52 qt SAE 80W-90.

Safety: the rules that prevent the worst injuries

  • Never clear a clog with the engine running, and never by hand. Kubota’s blower manual: “disengage the PTO… shut off the tractor engine, remove the ignition key, wait for all movement to stop, and then clear the snow from the chute.” Woods warns that “stored energy can cause auger to quickly rotate when unclogging occurs,” and says to use “a sturdy piece of wood.” Frontier (Deere) says to use only a 36-inch “piece of wood.” Bercomac says to wait 10 seconds and use a cleaning tool at least 3 feet long, “NEVER YOUR HANDS.” The CPSC says more than 40% of snow blower injuries treated in ERs in 2021 were to the wrist, hand and finger.
  • Keep every PTO guard on. Land Pride: the tractor PTO shield, gearbox shaft shield and driveline shields “must be secured in place” to avoid “injury or death from entanglement in driveline.” Ohio State Extension: “Safe operation of the PTO is not possible without these shields in place.” No loose scarves, drawstrings or untied boots near the shaft.
  • Shut down before you get off. Land Pride: disengage the PTO, set the parking brake, shut off the engine, remove the key, and wait for the PTO to stop before dismounting.
  • ROPS up, seatbelt on. Kubota recommends a ROPS and seat belt “in almost all applications.” Ohio State Extension says ROPS and seat belts are “99.9 percent effective in preventing deaths due to tractor overturns.” Don’t wear the belt with the ROPS folded down.
  • Ballast before loader work, and carry the bucket low (see above).
  • Watch where the snow goes. Never aim the chute at people, cars, windows or the road. Woods: “Never direct discharge toward people, animals, or property.” Check for kids, pets and mailboxes before you back up with a rear blower or blade.
  • Visibility. You’ll often work in the dark. Use your work lights, run the route in daylight first to mark hidden edges and drains, and stake the driveway edges before the ground freezes.

Using a walk-behind blower as well? See how to start a snow blower for choke and primer settings by brand, and snow blower auger not turning when the engine runs but nothing throws snow.

FAQ

Can a sub-compact tractor (Kubota BX, John Deere 1025R) run a snowblower? Yes. Kubota sells a 48 in front blower for the BX1880, BX2380, BX2680 and BX23S that runs off the mid-PTO, with a 350 lb rear counterweight. Small rear blowers start low too: Deere’s 48 in Frontier SB1148 is rated 16 to 35 PTO hp, and Deere shows its 47 in front blower on a 1025R. Compare those ranges with the PTO hp on your tractor’s spec sheet. Check the front-implement limits in your tractor’s manual.

Front blower or rear blower? A front blower lets you drive forward and see your work. It needs a mid-PTO, a front hitch and rear counterweight, and it costs more. A rear 3-point blower uses the standard 540 rpm PTO and hitch, so it fits more tractors. You’ll do most of the work in reverse.

Is a rear blade enough for snow? For light snow on a short drive, often yes. Land Pride rates its RBT blades for 17 to 40 hp tractors. Blades push snow, so in snowy regions the banks eventually run out of room. That’s when owners move to a blower.

Do I need chains on my tractor for snow? On packed snow and ice, chains plus 4WD and ballast give the most traction. Kubota’s BX blower manual says to make sure the machine is counterweighted and has tire chains “as recommended by your dealer.” Find your size with our chain size finder.

How much ballast do I need for a loader in snow? It depends on your tractor and loader. Kubota’s loader manuals say the amount “will depend on the application.” The one fixed figure we found is Kubota’s 350 lb rear counterweight for its BX front blowers. Use your loader manual’s ballast table, then see our loader ballast tables by tractor (Deere and Kubota manuals) and the ballast calculator for liquid-filled tires.

Sources

Accessed 2026-11-20. “Archive copy” means a maker’s manual hosted on a third-party site.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top