Quick answer: A two-stage snow blower has two belts with different part numbers: an auger belt (spins the auger and impeller) and a drive belt (turns the wheels or tracks). Find your model and serial number, then match your machine in the tables below, taken from each maker’s parts manual. Cub Cadet and Troy-Bilt manuals walk you through the auger belt yourself. Toro Power Max and Husqvarna ST manuals say to have a dealer do it.
Jump to the table: Cub Cadet and Troy-Bilt (MTD-built) ↓

Safety first, every time. Stop the engine, take out the key (or safety key) and pull the spark plug wire. MTD says to run the engine until it’s out of fuel before you tip the machine forward, and not to try draining fuel from the engine (MTD manual, p. 29). Ariens says to siphon the tank, run the engine until it stops, then close the fuel valve (Ariens Deluxe service manual, p. EN-7). Husqvarna starts with “Remove the fuel from the fuel tank” (Husqvarna ST manual, p. 18).
Every part number below is printed in a maker’s parts manual, parts supplement or parts catalog, linked with the page. If a source doesn’t say which belt is which, we say “confirm by model” instead of guessing. Not sure the belt is your problem? Start with our auger not turning guide.
Snow blower belt part numbers by brand and model
Buy by the number for your model, not by belt length. The same machine can change belts between serial ranges and engine sizes.
Cub Cadet and Troy-Bilt (MTD-built)
These come from the 2023 Cub Cadet and Troy-Bilt parts supplements, which sort the common 2- and 3-stage belts by engine size. Engine size (cc) is on the engine label and in your manual’s specs.
| Machine | Auger belt | Drive belt | Source |
|---|---|---|---|
| 2- and 3-stage, 208, 243 or 272 cc engine | 954-04050A | 954-04260 (wheel drive) | Cub Cadet 769-26938, p. 2; Troy-Bilt 769-26939, p. 1 |
| 2- and 3-stage, 277, 357 or 420 cc engine | 954-04195A | 954-04201A (wheel drive) | Same two supplements |
| Cub Cadet 2X 24 HP, 2X 26 HP, 2X 524 WE, 2X 524 SWE, 2X 526 SWE | 954-04050A | 954-04260 (wheel drive) | Cub Cadet 769-10811 (2015), p. 1 |
| Cub Cadet 2X 528 SWE; 3X 24, 26, 28 and 3X HD | 954-04195A | 954-04201A (wheel drive) | 769-10811, p. 1 |
| Cub Cadet 2X 30 PRO, 2X 34 PRO, 3X 30 PRO | 954-05153 | 954-05143 (wheel drive) | 769-26938, p. 2 |
| Cub Cadet 3X 30 PRO H, 3X 34 PRO H, 3X 34 PRO Hydro | 954-05144 | 954-05137 (transmission drive) | 769-26938, p. 2 |
| Cub Cadet single-stage | 754-04195A (its only belt) | None | 769-26938, p. 1 |
The 2015 and 2023 supplements agree: the smaller-engine machines use 954-04050A and 954-04260, and the larger ones use 954-04195A and 954-04201A. Yard Machines, Bolens and Craftsman 247.x machines are also MTD-built, but we didn’t find a parts list from those brands that prints their belt numbers, so check your model’s parts list.
Ariens
Ariens calls the auger belt the attachment drive belt. On the Deluxe and Professional models below, it’s a matched set of 2, sold as one part number.
| Model family (model numbers) | Auger belt | Drive belt | Source |
|---|---|---|---|
| Deluxe 24, 28, 30, 28 Track, 24 and 30 Platinum (921013, 017, 018, 022, 023, 031) | 07200514 (matched set) | 07200111 | Parts manual 04336000A, p. 7 |
| Deluxe 24, 27, 30 and Track, 2009 (921011 to 921019, 921305 to 921312) | 07200514 (matched set) | 07200111 | Parts manual 03882800A, p. 8 |
| Deluxe 30 (921020) | 07200521 (HA matched set) | 07200522 (3L) | 03882800A, p. 8 |
| Professional 28, 32, 36 (926038, 039, 040, 321, 322, 323) | 07200608 (matched set) | 07200607 | Parts manual 04337500C, pp. 7 and 21 |
| Pro 28 Track (926042, 926324) | 07200608 (matched set) | 07200505 | 04337500C, pp. 7 and 21 |
| Pro 32 12V (926513) | 07200430 (matched set) | 07200110 | 04337500C, pp. 7 and 21 |
| Compact 20, 22, 24 (920013, 014, 021, 316, 317, 321, 325, 326) | 07200513 | 07200603 | Parts manual 04632000, p. 7 |
| Compact 24 Track (920022, 920318) | 07200513 | 07200114 | 04632000, p. 7 |
| Sno-Tek 24 and 28 (920402, 403, 404) | 07200513 (402, 403) or 07238500 (404): confirm by model | 07200603 (Ariens’ part page calls it a traction belt) | Parts manual 04335300A, p. 7 |
| Deluxe 921045 and newer | No parts manual PDF found | Same | Ariens parts lookup, by model and serial number |
The 03882800A manual lists 07200514 as “V-Belt, HA Matched Set” and 07200111 as “V-Belt 3L”. The 04336000A manual names 07200514 the auger set and 07200111 the drive belt, and Ariens’ own part pages agree: 07200514 is an “Attachment V-belt, Set Of 2” and 07200111 a “Traction Drive Wrapped V-belt.” Ariens’ page for 07200603 calls it a traction drive belt for current Classic and Compact models. The Compact auger belt, 07200513, has no part page on ariens.com today, so ask Ariens or a dealer for the current number before you order.
Toro
Toro’s parts catalogs list both belts on one page as “Belt-V” without saying which is the auger/impeller belt and which is the traction belt. The exploded views don’t settle it either, so confirm by model before you order.
| Model (serial range) | Belts listed | Which is which | Source |
|---|---|---|---|
| Power Max 824 OE, 37798 (SN 415200000 and up) | 120-3892 and 120-3893 | Confirm by model | Parts catalog 3464-442, p. 19 (same in 3446-737 and 3443-504) |
| Power Max 826 OE, 38817 (SN 314000001 and up) | 120-3892 and 120-3893 | Confirm by model | Parts catalog 3378-841, p. 11 |
| Power Max HD 926 OXE, 38820 (SN 400010798 and up) | 119-1564 and 125-1145 | Confirm by model | Parts catalog 3406-950, p. 17 |
| Power Max HD 824, 39960, and HD 828, 39961 (SN 400000000 and up) | 161-5972 (Belt-V) and 145-4143 (Belt 3L) | Confirm by model | 3481-505, p. 7; 3481-506, p. 7 |
Husqvarna and Briggs & Stratton
| Machine | Auger belt | Drive belt | Source |
|---|---|---|---|
| Husqvarna ST 327P (Mfg. ID 96191008300 to 96191008303, 96193009201, 96193009203) | 532 41 98-88 (listed as “impeller belt”) | 532 41 35-92 (traction belt) | Illustrated parts lists, e.g. 96191008302, p. 17; 96191008300, p. 16; 96193009201, p. 18 |
| Briggs & Stratton 1227MD, 27 in (Mfg. No. 1696619-02) | 707584 (2 required) | 707585 (traction drive) | Parts manual, p. 21 |
| Briggs & Stratton 1530MDS, 30 in (Mfg. No. 1696828-00) | 770796 | 770799 (traction drive) | Parts manual, p. 13 |
Husqvarna’s parts list calls the auger belt the “impeller belt”. It’s one of only two belts on the machine, and the operator’s manual calls the pair the auger belt and the drive belt. For other ST models, look up the parts list for the manufacturing ID on your product label. The Briggs parts manuals are Briggs & Stratton documents hosted by a retailer.
Honda HSS: we didn’t find a Honda parts document that prints the belt numbers, and Honda lists the auger belt as a dealer service item (more on that below). Get the number from a Honda dealer with your frame serial number. Craftsman (CMXGBAM): the operator’s manual we checked lists shear pins but no belts, so look up your model in Craftsman’s parts lookup.
Auger belt or drive belt? How to tell which one failed
Look at what still works:
- Wheels drive, but the auger and impeller don’t turn: the auger belt, a broken shear pin or the auger cable. Our auger not turning guide runs those checks in order, and the shear pin lookup has the pin numbers.
- Auger throws snow, but the machine won’t move itself: the drive belt, the drive cable or the friction wheel (see snow blower won’t move for the push test and cable settings by brand). MTD lists all three under “Fails to Propel Itself” (MTD, p. 27), and Ariens points to the traction drive belt and cable (Ariens Deluxe manual, p. 24).
- Squeal when you engage a lever: a slipping belt, a cable out of adjustment, or a frozen impeller. Ariens’ fix for a slipping auger belt is “Replace belt or adjust auger control cable” (p. 24), so check the cable first.
- What a worn belt looks like: Toro says to replace a belt that’s “worn, oil-soaked, excessively cracked, frayed, or otherwise damaged” (Toro Power Clear 721 R/E manual, p. 16). A belt that has rolled off its pulley or looks shiny and glazed is also suspect.
If the engine won’t start at all, the belts aren’t the problem yet. Start with snow blower won’t start.
Find your model and serial number
You need both. Several of the Ariens and Toro rows above change belts by serial range.
- Cub Cadet, Troy-Bilt and other MTD-built machines: stand at the operator’s position and look at the rear, right side of the engine (MTD, p. 1).
- Ariens: the model and serial number decal on the unit. The manual’s Figure 1 shows where (Ariens Deluxe manual, p. 3).
- Toro: the serial number decal. Figure 1 in the operator’s manual shows where, and the decal’s QR code opens the parts information for your machine (Toro Power Max 824 OE manual).
- Husqvarna: the product label with the model and the manufacturing ID (Mfg. ID). Husqvarna’s parts lists are filed by Mfg. ID, not just by model.
- Honda HSS: record both the engine and the frame serial numbers. Honda says you’ll need them when ordering parts (Honda HSS724A manual, p. 21).
- Briggs & Stratton: the parts manuals are filed by manufacturing number (Mfg. No.) as well as model, like 1696619-02 for a 1227MD.
Can you replace it yourself? What each maker says
- Cub Cadet and Troy-Bilt (MTD-built): the auger belt is a do-it-yourself job with steps in the manual (pp. 29 to 30). The drive belt isn’t: “See your authorized service dealer to have drive belt replaced or contact Customer Support” (MTD, p. 30).
- Ariens Deluxe: the operator’s manual sends you to the service manual for both belts (p. 24). The Deluxe service manual has the steps for both, with a caution: “Be aware of your mechanical aptitude… If you are not comfortable or capable of completing service and / or repairs to the machine, take the machine to an authorized AriensCo service dealer” (p. EN-1).
- Toro Power Max: if either belt “becomes worn, oil-soaked, or otherwise damaged, have an Authorized Service Dealer replace the belt” (Toro Power Max 824 OE manual, p. 24). Toro also has a dealer inspect both belts yearly or before storage (p. 18).
- Husqvarna ST: the belts “are not adjustable.” Husqvarna recommends a qualified service center, and replacing the drive belt and auger belt at the same time (Husqvarna ST manual, p. 18). The job means separating the machine in two.
- Honda HSS: the auger belt is a dealer service item unless “you have the proper tools and are mechanically proficient” (Honda HSS724A manual, p. 14). A worn belt or one that’s off its pulleys: “see dealer” (p. 20).
- Toro Power Clear (single-stage): one belt, and the manual gives the replacement steps (p. 16), though its schedule has a dealer inspect the belt (p. 12).
How to replace a snow blower auger belt (Cub Cadet and Troy-Bilt)
These steps are from MTD’s manual for Cub Cadet and Troy-Bilt 2- and 3-stage machines (500, 600 and 800 Series). Other brands differ, so use your own manual.
- Run the engine until it’s out of fuel. Don’t try to drain fuel from the engine. Remove the safety key or disconnect the spark plug wire. If your machine has cordless battery start, take the battery out.
- Remove the plastic belt cover on the front of the engine (two self-tapping screws). If there’s an LED light bar on the auger housing, unplug its wire harness first.
- Roll the auger belt off the engine pulley.
- Carefully pivot the snow blower up and forward so it rests on the auger housing.
- Remove the frame cover from the underside (self-tapping screws).
- Remove the shoulder bolt that acts as a belt keeper, and unhook the spring from the frame.
- Slip the belt off the auger pulley, between the support bracket and the pulley. Engaging the auger control makes this easier.
- Install the new belt in reverse order. Put the shoulder bolt back and reconnect the spring. MTD calls this out specifically.
- Test the auger control before you use the machine (p. 17).
Source: MTD manual 769-26795, pp. 29 to 30. The same manual tells you to take the drive belt to a dealer.
On an Ariens Deluxe, the service manual has you separate the auger housing from the frame to reach the belts. It warns that the attachment sheave’s edges are sharp, so wear thick gloves (p. EN-9). On reassembly it gives a torque for the housing bolts (24.9 to 51.7 lb-ft) and has you readjust the skid shoes (p. EN-10). Our gravel driveway guide has the skid shoe settings by brand.
After you replace a belt: check the controls
A new belt changes how the controls engage, so check them before the next storm:
- Auger stop test: Ariens says the auger and impeller must stop within 5 seconds when you release the attachment clutch lever, and the belt finger must sit less than 1/8 in from the belts without touching them (Ariens service manual, p. EN-11). MTD wants “NO signs of motion” (p. 17).
- Cable adjustment: Husqvarna says to adjust the auger control cable after an auger belt change (p. 20). The settings for each brand are in the cable table in our auger not turning guide.
- Start it up the right way: how to start a snow blower has the start sequence by brand.
Running the tank dry for a belt job is a good time for the yearly oil change too. Our snow blower oil guide has the type and amount by engine.
Buying the right belt: OEM number, not length
- Measuring the old belt can mislead you. A worn belt has stretched. The parts manuals also specify belt sections, not just lengths: Ariens’ Deluxe manual lists a 3L drive belt next to an “HA matched set” for the auger (03882800A, p. 8), and Toro’s HD 824 catalog lists one “Belt 3L” next to a plain “Belt-V” (p. 7).
- Construction matters. Husqvarna’s manual says its V-belts “are of special construction and should be replaced by original equipment manufacturer (OEM) belts… Using other than OEM belts can cause personal injury or damage to the product” (p. 18). Ariens sells 07200111 as a “wrapped” V-belt.
- Matched sets come as one part number. The Ariens auger belts above (07200514, 07200608, 07200430) are pairs. Briggs lists two 707584 auger belts on the 1227MD.
- Superseded numbers: if the number in your manual won’t come up, ask the maker or a dealer for the current one. None of the sources above shows a belt supersession, so we don’t print any. Don’t trust a cross-reference unless the maker confirms it.
Part of our snow blower maintenance guide: see the maintenance schedule for your brand, with each maker’s intervals from the manual.
FAQ
How long does a snow blower belt last? None of the manuals we checked gives a life in hours or seasons. Replace a belt when it slips under load, squeals, or looks worn, cracked, frayed, glazed or oil-soaked. Toro has a dealer inspect both belts on its Power Max yearly or before storage.
Should I replace both belts at the same time? Husqvarna recommends it for its ST machines, since both belts come off in the same job. MTD’s manual covers only the auger belt as a do-it-yourself job and sends you to a dealer for the drive belt. On Ariens Deluxe and Pro models, the auger belt is itself a matched set of 2, so always replace both of those together.
Why does my new snow blower belt squeal? Usually the control cable needs adjusting after the belt change (Husqvarna says to adjust it after an auger belt change), or the belt is wrong for the machine. Ariens also lists a frozen impeller as a cause of a belt that squeals continuously. Check the cable and confirm the part number against your model’s parts list.
Can I use a lawn mower belt on my snow blower? No. Use the belt number from your snow blower’s parts list. Husqvarna says its snow blower belts are of special construction and to use OEM belts, and a belt that only looks the same length can be a different section or construction.
How many belts does a single-stage snow blower have? One. The Toro Power Clear 721 has a single drive belt that turns the rotor (manual, p. 16). Cub Cadet’s single-stage machines use auger drive belt 754-04195A (769-26938, p. 1), and Ariens sells 07200627 as the poly V-belt for its Professional 21 and Path-Pro single-stage models.
Sources
- Cub Cadet, Parts/Warranty Supplement 769-26938 (December 13, 2023): single-stage, p. 1; 2- and 3-stage belts, p. 2
- Troy-Bilt, Registration, Parts and Warranty Supplement 769-26939 (December 13, 2023), p. 1
- Cub Cadet, Parts/Warranty Supplement 769-10811 (May 20, 2015), p. 1
- MTD (Cub Cadet, Troy-Bilt), 2-Stage and 3-Stage Snow Blower Operator’s Manual 769-26795 (2023): model plate, p. 1; auger control, p. 17; troubleshooting, p. 27; auger belt and drive belt, pp. 29 to 30
- Ariens, parts manuals: 04336000A (921 Series, 10/11), p. 7; 03882800A (Deluxe, 9/09), p. 8; 04337500C (926 Series, 7/12), pp. 7 and 21; 04632000 (Compact, 8/13), p. 7; 04335300A (Sno-Tek, 10/11), p. 7
- Ariens, Deluxe Series Service Manual 05135630B (12/19): pp. EN-1, EN-7 and EN-9 to EN-11
- Ariens, Deluxe Series Operator’s Manual 30219300A (9/24): model decal, p. 3; troubleshooting, p. 24
- Ariens part pages: 07200514, 07200111, 07200608, 07200603, 07200627 (checked November 2026)
- Toro, parts catalogs: 3464-442 Rev C (Power Max 824 OE 37798), p. 19; 3378-841 (Power Max 826 OE 38817), p. 11; 3406-950 Rev B (Power Max HD 926 OXE 38820), p. 17; 3481-505 Rev B (Power Max HD 824 39960), p. 7; 3481-506 Rev B (Power Max HD 828 39961), p. 7
- Toro, Power Max 824 OE Operator’s Manual 3415-760: maintenance schedule, p. 18; drive belts, p. 24
- Toro, Power Clear 721 R/E Operator’s Manual 3423-722: maintenance schedule, p. 12; replacing the drive belt, p. 16
- Husqvarna, ST 327P illustrated parts lists by Mfg. ID: 96191008302, p. 17; 96191008300, p. 16; 96193009201, p. 18
- Husqvarna, ST 224 / ST 227P / ST 230P / ST 224P Operator’s Manual (2019): belts, p. 18; auger control cable, p. 20
- Briggs & Stratton, parts manuals (retailer-hosted copies): 1227MD, Mfg. No. 1696619-02 (2017), p. 21; 1530MDS, Mfg. No. 1696828-00 (2017), p. 13
- Honda, HSS724A Owner’s Manual: maintenance schedule, p. 14; troubleshooting, p. 20; serial numbers, p. 21
More snow blower fixes: auger not turning · shear pin lookup · how to start a snow blower · snow blower won’t start · snow blower oil



