Quick answer: If the engine runs but your snow blower won’t move, shut it off, pull the key and the spark plug wire, and push it. With the drive lever released, it should roll freely. With the drive lever held, the wheels should lock. That’s the check in the Cub Cadet and Troy-Bilt (MTD) manual. Still rolls with the lever held: the drive cable is slack, or the friction wheel (friction disc) is worn. Locks but won’t drive under power: the drive belt. Won’t roll at all, or creeps forward on its own: the cable is too tight, or the drive is frozen. Adjust the cable first, then check the friction wheel, then the belt.
Jump to the table: The 2-minute drive test ↓

Safety first, every time: stop the engine, take out the key (or safety key) and pull the spark plug wire before you touch the drive. Every check that needs the engine running is spelled out below, step by step, from the maker’s manual. Most fixes mean tipping the machine forward onto the auger housing, and the makers handle the fuel differently:
- Cub Cadet and Troy-Bilt (MTD-built): run the engine until it’s out of fuel. “Do not attempt to drain fuel from engine.” Then pivot it up and forward onto the auger housing (MTD manual 769-26795, p. 30).
- Toro Power Max: drain the fuel from the tank, then tip the machine forward onto its auger housing “and block it so that it cannot fall” (Toro Power Max 824 OE manual, p. 22).
- Ariens Deluxe: drain the fuel from the tank and fuel system before putting the unit in its service position, and make sure it “will not tip” (Ariens Deluxe service manual, p. EN-19).
Every spec and part number on this page comes from a maker’s operator’s manual, service manual, parts list or support page, linked with the page. Where a source doesn’t give one, we say so. If the auger is the part that won’t turn, see our auger not turning guide instead. If the engine won’t run at all, start with snow blower won’t start.
The 2-minute drive test
This is MTD’s drive control check for Cub Cadet and Troy-Bilt 2- and 3-stage machines (MTD manual, p. 18), done with the engine off:
- With the drive control lever released, push the snow blower gently forward. It should roll freely.
- Engage the drive control lever and gently try to push it forward. The wheels should not rotate or roll freely.
- If it has a shift lever, with the drive lever released, move the shift lever back and forth between R2 and F6 several times. There should be no resistance.
“If any of the above tests fail, the drive cable is in need of adjustment,” MTD says. Here’s how to read the result on any friction-drive machine:
| What you find | Most likely cause | Check | Fix |
|---|---|---|---|
| Rolls freely even with the drive lever held | Drive cable slack, or a worn, glazed or oily friction wheel | Cable slack first, then look at the friction wheel | Adjust the cable. If that doesn’t fix it, replace the friction wheel (MTD, p. 30) |
| Locks with the lever held, but won’t drive with the engine running | Drive belt loose, worn, broken or off its pulley | Belt cover off, engine off | Replace or reinstall the belt. MTD and Honda say to see a dealer |
| Won’t roll with the lever released | Drive cable too tight, or ice in the drive | Look for cable tension at rest, and for ice under the frame | Loosen the cable. Thaw a frozen drive, don’t force it |
| Moves when you let go of the drive lever | Drive cable too tight | Toro and Husqvarna both point to the cable | Stop using it and readjust the cable (Toro, p. 8) |
| Shift lever is stiff, or it drives in some speeds only | Drive cable, or the shift cable or rod out of adjustment | Push test, then the full range of speeds | Adjust the drive cable, then the shift cable or rod (MTD, pp. 17 to 18) |
| Drives with one wheel, or pulls to one side | Uneven tire pressure, or a wheel lock pin out | Tire pressure, and the pin through each wheel hub | Equalize the pressure. Replace the pin (Husqvarna, p. 23) |
Hydrostatic machines like the Honda HSS and Cub Cadet Hydro models don’t use this push test. Skip to hydrostatic and track machines.
The running check, from the manuals
After any adjustment, the makers test it under power. Stay behind the handles, on a clear, level surface:
- Toro Power Max 824 OE: start the engine, put the speed selector in R1 and squeeze the traction lever. The machine should move rearward. Release it, select speed 1 and squeeze again. It should move forward. If it doesn’t, release the lever, shut off the engine and adjust the trunnion on the speed-control rod (down for reverse, up for forward), then repeat until no adjustment is needed (p. 8).
- Husqvarna: start the engine, move the drive speed control lever up from the middle, and push and hold the drive engagement lever. “The snow blower should move forwards.” Release it, and it “should stop immediately” (Husqvarna support).
- Ariens Deluxe: the wheels or tracks “must stop quickly when traction drive clutch lever is released” (Ariens Deluxe manual, p. EN-15).
Snow blower drive cable adjustment by brand
The drive cable (Toro calls it the traction cable, Ariens the traction drive clutch cable, Husqvarna the drive engagement cable) stretches with use. When it does, the friction wheel never presses hard enough on the drive plate. Ariens says it plainly: “If unit does not drive correctly, adjust traction clutch to compensate for friction disc wear” (p. EN-22).
| Machine (manual) | Adjuster | Correct setting | Source |
|---|---|---|---|
| Cub Cadet / Troy-Bilt 2- and 3-stage, non-hydro | Loosen the two hex screws on the drive cable bracket. Bracket up for more slack, down for more tension | Released: “very little slack. It should NOT be tight.” Then pass the push test | MTD 769-26795, p. 18 |
| Cub Cadet / Troy-Bilt Hydro models | Loosen the upper hex screw on the drive cable bracket. Up for slack, down for tension | “Very little slack,” not tight. Check for excessive slack | MTD 769-26795, p. 18 |
| Ariens Deluxe 24, 28, 30 (921069 to 921072) | Loosen the jam nut on the traction cable adjustment barrel, turn the barrel down to shorten the cable | Cable slack removed. With the clutch disengaged, the drive plate touches the stop bolt | Ariens 30219300A, p. EN-22 |
| Toro Power Max 824 OE | Loosen the jam nut, hold the traction lever engaged, turn the turnbuckle | Spring length 2.18 in (5.5 cm), slight tension on the cable | Toro 3415-760, p. 20 |
| Husqvarna (support article) | Hold the adjustment screw, loosen the locknut. Clockwise adds tension | Drives when the lever is held, stops “immediately” when released | Husqvarna KA-70373 |
| Honda HSS724A | Drive clutch cable is a dealer item, unless you have the tools and skills | Not given | Honda manual, p. 14 |
Don’t overtighten it. Husqvarna warns: “Too much tension can cause the snow blower to move forwards on its own, leading to potential injury or damage.” Toro’s version: if the traction drive isn’t adjusted properly, “the machine may move in the direction opposite of what you intended” (p. 8). A machine that creeps with the lever released has a cable that’s too tight. Back it off before you use it again.
When the cable isn’t the fix: Toro says if the traction cable is properly adjusted “but a problem remains, contact an Authorized Service Dealer” (p. 20). MTD and Ariens point to the friction wheel next.
Toro schedule: inspect the traction cable after the first 2 hours of use, then yearly (p. 18).
Friction wheel (friction disc): inspection and part numbers
On a friction-drive two-stage machine, a rubber-rimmed wheel on a hex shaft presses against a spinning metal drive plate. The drive cable pushes them together. Moving the shift lever slides the wheel across the plate to change speed and direction. When the rubber wears, cracks, glazes or gets oily, the plate spins and the wheel slips.
How to inspect it (Cub Cadet and Troy-Bilt): run the engine out of fuel and pull the safety key or plug wire, tip the machine forward onto the auger housing, and remove the four self-tapping screws holding the frame cover underneath. “Inspect friction wheel for signs of wear or cracking” (MTD manual, p. 30). Then put the frame cover back.
Keep grease and oil off it. All three makers say so:
- MTD: coat the hex shaft lightly with Bostik Never-Seez once a season or every 25 hours, but “be careful not to get any lubricant on aluminum drive plate or rubber friction wheel. Doing so will affect the drive system” (p. 28).
- Ariens: “DO NOT allow grease or oil to contact friction disc, friction plate or belts” (Ariens Deluxe manual, p. EN-16).
- Toro: oil the hex shaft yearly with automotive engine oil, but “Do not get oil on the rubber wheel or the steel friction pulley because the traction drive will slip” (Toro, p. 22).
A wet friction disc slips too. Husqvarna’s fix for a wet disc is “Let the friction disc dry” (Husqvarna ST manual, p. 23).
Who replaces it?
- Cub Cadet and Troy-Bilt steerable 500 and 800 Series, and non-steerable single-speed 600 Series: “Special tools are required and several components must be removed in order to replace the friction wheel rubber. See your authorized service dealer” (MTD, p. 30).
- Multi-speed non-steerable 600 Series: the manual gives the steps (pp. 30 to 31). Put the shift lever in F1, remove the right-hand wheel, the hex nut and the bearing, and slide the friction wheel off the hex shaft. If you replace only the rubber ring, tighten the four side-plate screws one turn at a time, turning the wheel between screws, to 115 to 145 in-lbs. Then do the drive control test again.
- Ariens Deluxe (921045 and newer): the service manual has the remove and install steps for the friction disc assembly (05135630B, pp. EN-19 to EN-21), ending with a speed selector adjustment. Ariens’ operator’s manual says “Replace friction disc. Refer to the Service Manual for your unit” (p. EN-24).
- Husqvarna ST: “The friction drive wheel is worn. Contact an authorized service center” (p. 23).
- Toro Power Max: the operator’s manual has no friction wheel steps. Toro sends you to a dealer when an adjusted cable doesn’t fix it (p. 20).
Friction wheel part numbers by brand
Buy by the number for your model and serial number. These are printed in each maker’s parts list.
| Machine | Part | OEM number | Source |
|---|---|---|---|
| Cub Cadet and Troy-Bilt 2- and 3-stage (2023 supplements) | Friction wheel rubber | 935-04054A | Cub Cadet 769-26938, p. 2; Troy-Bilt 769-26939, p. 1 |
| Cub Cadet and Troy-Bilt 2- and 3-stage (2023 supplements) | Friction wheel assembly | 684-04153C | Same two supplements |
| Cub Cadet 2X and 3X (2015 supplement) | Friction wheel rubber (“all models”) / assembly | 935-04054 / 684-04153C | Cub Cadet 769-10811, p. 1 |
| Ariens Deluxe 24, 27, 30 and Track, 2009 parts manual (all models) | Friction disc | 00170800 | Ariens 03882800A, p. 11 |
| Ariens Deluxe and Platinum 921013, 017, 018, 022, 023, 031 | Friction disc | 00170800 | Ariens 04336000A, p. 9 |
| Ariens Professional 926038, 039, 040, 042, 513, 321 to 324 | Friction disc | 00170800 | Ariens 04337500C, p. 14 |
| Ariens Compact 920013, 014, 021, 316, 317, 321, 325, 326 | Friction disc | 00170800 | Ariens 04632000, p. 15 |
| Ariens Sno-Tek 920402, 403, 404 | Friction disc | 00170800 | Ariens 04335300A, p. 9 |
| Toro Power Max 826 OE (38817, SN 314000001 and up) | Wheel-Friction | 119-1567 | Toro 3378-841, p. 7 |
| Toro Power Max 824 OE (37798, SN 415200000 and up) | Wheel-Friction | 119-1567 | Toro 3464-442, p. 11 |
| Toro Power Max HD 824 (39960, SN 400000000 and up) | Wheel-Friction | 119-1567 | Toro 3481-505, p. 21 |
| Husqvarna ST, Honda HSS, newer Ariens Deluxe | Not found in the documents we checked | Confirm by model | Your model’s parts list or a dealer |
The 2015 Cub Cadet supplement lists 935-04054 for “all models”, and the 2023 supplements list 935-04054A. Don’t assume they’re interchangeable unless Cub Cadet confirms it. Not sure which model you have? Our belt replacement guide shows where each maker puts the model and serial number.
Is it the drive belt?
The drive belt runs from the engine pulley to the drive plate. If it’s off its pulley, broken or badly worn, the push test usually passes (the wheels lock when you hold the lever), but nothing moves with the engine running. MTD’s “Fails to Propel Itself” list has three causes: the drive cable, a loose or damaged drive belt, and a worn friction wheel (p. 27). Ariens adds a speed selector out of adjustment (p. EN-24).
On MTD-built machines, the drive belt is a dealer job: “See your authorized service dealer to have drive belt replaced or contact Customer Support” (p. 30). Honda lists a worn, broken or off-pulley drive belt as “See servicing Honda snow blower dealer” (Honda manual, p. 20). The drive belt part numbers by brand and model, and who can fit them, are in our snow blower belt replacement guide.
Only drives in some speeds? Check the shift linkage
If it drives in some gears but not others, or won’t reach every forward and reverse speed, the shift linkage is out of adjustment.
- Cub Cadet and Troy-Bilt with a shift cable: “If full range of speeds (forward and reverse) cannot be achieved,” put the shift lever in the fastest forward speed, loosen the hex nut on the shift cable index bracket, pivot the bracket down to take up the slack, and retighten to 100 to 120 in-lbs. If that’s not enough, move the cable to another hole in the bracket (MTD, p. 17).
- Cub Cadet and Troy-Bilt with a shift rod: in the fastest forward speed, remove the cotter pin and washer and pull the ferrule out of the shift lever. Rotate the transmission shift lever down as far as it goes, turn the ferrule on the rod until it lines up with the upper hole, and pin it back in (pp. 17 to 18).
- Ariens Deluxe: disconnect the adjustment pivot pin, put the speed selector in fastest forward, turn the speed selector arm down as far as it goes, then thread the pivot pin along the shift rod until it lines up and reconnect. Check that it moves forward in first and backward in first reverse (p. EN-19).
- Toro Power Max: the trunnion adjustment in the running check above (p. 8).
Change speeds the way the manuals say, too. MTD: “Always release drive control lever before changing speeds” on all but hydro models, or you’ll increase wear on the drive system (p. 21). Toro: “To change speeds, release the traction lever” (p. 14).
Other causes: frozen drives, wheel pins and the hex shaft
- Frozen drive. Ice on the drive plate or friction wheel after a wet day can lock the drive or make it slip. Toro says moving parts may freeze, and “Do not use excessive force when trying to operate frozen controls” (p. 17). Thaw it somewhere warm, and let a wet friction disc dry (Husqvarna, p. 23).
- Wheel pins. If it drives on one wheel only, Husqvarna says to “Inspect the tire lock pin” (p. 23). Toro’s parts lists show the wheels held on by pins (107-3039, two per machine, on the Power Max 826 OE, p. 7). A missing pin can leave that wheel turning free on its axle.
- Hex shaft and wheel axles. A dry, rusty hex shaft makes shifting stiff. Lube it on schedule (MTD once a season or every 25 hours, Toro yearly), and keep the lube off the rubber. MTD also has you pull both wheels once a season and grease the axles with multipurpose automotive grease (p. 28).
- Track machines packed with ice. Husqvarna lists “excessive snow and ice build up in between track components” as a cause of lost drive. Clear it out (p. 23).
Tire pressure and flat tires
Low or uneven tires cost you traction and make the machine pull to one side. Husqvarna and Toro both list unequal tire pressure in their troubleshooting.
| Machine | Tire pressure | What else the manual says | Source |
|---|---|---|---|
| Toro Power Max 824 OE | 17 to 20 psi (116 to 137 kPa) | Check yearly or before storage | Toro, p. 18 |
| Toro Power Max HD 928 / 1028 OHXE | 17 to 20 psi (116 to 137 kPa) | Tires are overinflated for shipping. Reduce both equally | Toro 3385-239, p. 12 |
| Husqvarna ST 224, ST 227P, ST 224P | 18 psi maximum operating | ST 230P: 20 psi maximum | Husqvarna, p. 24 |
| Honda HSS724A, wheel type | 20 psi (138 kPa) | Don’t inflate beyond 20 psi | Honda, p. 16 |
| Cub Cadet / Troy-Bilt (MTD) | Use the tire sidewall | Tires are over-inflated for shipping. Keep both equal | MTD, p. 15 |
| Ariens Deluxe | Use the tire sidewall | “Keep tires inflated to pressure listed on tire sidewall” | Ariens, p. EN-15 |
Seating a tire bead is where people get hurt. MTD warns: “Under any circumstance do not exceed manufacturer’s recommended psi… Excessive pressure when seating beads may cause tire/rim assembly to burst with force sufficient to cause serious injury” (p. 15).
Flat tire? Cub Cadet’s parts supplement lists its own tire and tube sealant (490-325-0020, 32 oz; 490-325-0022, 16 oz) (769-26938, p. 2). For a tire that won’t hold air, get the tire or wheel assembly number from your model’s parts list.
Hydrostatic and track machines (Honda HSS, Cub Cadet Hydro)
A hydrostatic machine drives through a hydraulic transmission, so the push test above doesn’t apply. Stick to what these manuals say:
Honda HSS724A (hydrostatic, wheel and track types):
- To move it by hand, pull both steering control levers at the same time. That disengages the transmission, and the machine “is free to maneuver (push or pull) by hand with or without the engine running” (p. 9).
- Engine runs, but it doesn’t move (p. 20): the drive clutch lever is disengaged (engage it), the shift lever is in N (move it to F or R), the drive clutch lever mechanism or cable isn’t working (see a Honda dealer), or the drive belt is worn, broken or off the pulleys (see a dealer).
- Warm up the transmission: with the shift lever in N, squeeze the drive clutch lever for about 30 seconds while the engine warms up (p. 10).
- Track tension (track type): with the tracks clean and dry, press down midway between the wheels with 11 lbf. Deflection should be 7/16 to 5/8 in (11 to 16 mm). Adjust at the rear axle tension bolts, then torque the lock nuts to 16 ft-lb (p. 16).
- Dealer items: the drive clutch cable and the drive belt, “unless you have the proper tools and are mechanically proficient” (p. 14).
Cub Cadet Hydro models (MTD 769-26795):
- To move it without starting the engine, squeeze both the right and left steering triggers to disengage the drive (p. 22).
- Drive cable: “very little slack. It should NOT be tight.” Adjust at the upper hex screw on the drive cable bracket (p. 18).
- Belt: the 3X PRO Hydro uses a transmission drive belt, 954-05137 (769-26938, p. 2). Fitting is a dealer job (p. 30).
Steering-trigger and Auto-Turn machines still have a friction disc. Trigger steering (MTD’s steerable 500 and 800 Series), Toro’s wheel clutch levers on the Power Max HD 928 and 1028 OHXE (Toro 3385-239, p. 18) and Ariens Auto-Turn (p. EN-12) only steer the wheels. The Ariens Deluxe with Auto-Turn lists a worn friction disc as a cause of no drive (p. EN-24), so use the friction-drive checks above.
Part of our snow blower maintenance guide: see the maintenance schedule for your brand, with each maker’s intervals from the manual.
FAQ
Why does my snow blower only drive in some speeds? The shift cable or shift rod is out of adjustment, or the friction wheel is worn. MTD says to adjust the shift cable or rod “if full range of speeds (forward and reverse) cannot be achieved.” Ariens lists a speed selector out of adjustment as a cause of a unit that won’t drive forward or in reverse.
Why does my snow blower move when I let go of the drive lever? The drive cable is too tight. Husqvarna warns that too much tension “can cause the snow blower to move forwards on its own,” and Toro says to check the traction cable if the machine moves with the lever released. Stop using it until the cable is readjusted.
How long does a snow blower friction disc last? None of the manuals we checked gives a life in hours or seasons. Ariens has you take up cable slack “to compensate for friction disc wear,” and MTD says to check the friction wheel when a cable adjustment doesn’t fix the drive. Replace it if it’s worn, cracked, glazed or oil-soaked.
Can I use my snow blower if the self-propel doesn’t work? You can move it by hand. On friction-drive machines, it rolls with the drive lever released. On hydrostatic machines, Honda says to pull both steering levers and Cub Cadet says to squeeze both steering triggers to free the drive. Pushing a two-stage machine through deep snow is hard work, so fix the drive before the next storm.
How much does a friction wheel cost? We don’t list prices. Get the OEM number from your model’s parts list (the table above has the common ones), then check with the maker or a dealer. On some MTD-built machines you can replace just the rubber ring (935-04054A) instead of the whole assembly (684-04153C).
What PSI should snow blower tires be? Use your manual. Toro Power Max: 17 to 20 psi. Honda HSS724A: 20 psi, no more. Husqvarna ST: 18 psi maximum on most models, 20 on the ST 230P. Cub Cadet, Troy-Bilt and Ariens send you to the number on the tire sidewall. Keep both tires equal.
Sources
- MTD (Cub Cadet, Troy-Bilt), 2-Stage and 3-Stage Snow Blower Operator’s Manual 769-26795 (April 2023): tire pressure, p. 15; shift cable and rod, pp. 17 to 18; drive control (non-hydro and hydro), p. 18; drive control lever, p. 21; steering triggers, p. 22; troubleshooting, p. 27; lubrication, p. 28; drive belt and friction wheel, pp. 30 to 31
- Cub Cadet, Parts/Warranty Supplement 769-26938 (December 13, 2023), p. 2
- Troy-Bilt, Registration, Parts and Warranty Supplement 769-26939 (December 13, 2023), p. 1
- Cub Cadet, Parts/Warranty Supplement 769-10811 (May 2015), p. 1
- Ariens, Deluxe Sno-Thro Operator’s Manual 30219300A (2024): Auto-Turn, p. EN-12; clutch and tire checks, p. EN-15; lubrication, p. EN-16; speed selector, p. EN-19; traction drive clutch, p. EN-22; troubleshooting, p. EN-24
- Ariens, Deluxe Service Manual 05135630B (2019): friction disc replacement, pp. EN-19 to EN-21
- Ariens parts manuals: 03882800A, p. 11; 04336000A, p. 9; 04337500C, p. 14; 04632000, p. 15; 04335300A, p. 9
- Toro, Power Max 824 OE Operator’s Manual 3415-760: traction drive check, p. 8; speed selector, p. 14; freeze-up, p. 17; maintenance schedule, p. 18; traction cable, p. 20; hex shaft, p. 22
- Toro, Power Max HD 928/1028 OHXE Operator’s Manual 3385-239: tire pressure, p. 12; wheel clutch levers, p. 18
- Toro parts catalogs: 3378-841, p. 7; 3464-442, p. 11; 3481-505, p. 21
- Husqvarna, ST 224 / ST 227P / ST 230P / ST 224P Operator’s Manual (2019): troubleshooting, p. 23; technical data, p. 24
- Husqvarna support, Adjusting the snow blower’s drive engagement cable and Loss of traction drive or slowing of drive speed
- Honda, HSS724A Owner’s Manual: steering levers, p. 9; transmission warm-up, p. 10; maintenance schedule, p. 14; track and tires, p. 16; troubleshooting, p. 20
More snow blower fixes: auger not turning · belt replacement · shear pin lookup · how to start a snow blower · snow blower oil · gas and fuel stabilizer



