Chart of snow blower engine oil type and capacity for Briggs, Tecumseh, MTD, Toro, Ariens, Honda and Husqvarna engines, from the manuals

Snow Blower Oil: What Type and How Much, by Engine

Quick answer: Most snow blower engines take 5W-30, and the engine manuals say so. Briggs & Stratton recommends Synthetic 5W-30 for its Snow Series engines. Tecumseh (Snow King), MTD (the engines in Cub Cadet and Troy-Bilt machines), Toro, Ariens AX, Honda GX and Husqvarna’s LCT engines all list 5W-30 for winter. For extreme cold, MTD’s 179 to 243cc manual and Tecumseh’s manual list 0W-30 synthetic. Capacity runs from 16 oz to about 38 oz depending on the engine, so fill to the dipstick, not by the bottle.

Jump to the table: What oil does a snow blower take? (by engine) ↓

Chart of snow blower engine oil type and capacity for Briggs, Tecumseh, MTD, Toro, Ariens, Honda and Husqvarna engines, from the manuals

YardGuides may earn a commission from links on this page, at no cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more.

Every figure below comes from the engine or snow blower maker’s own manual, and each one is linked with its page number. If a manual doesn’t print a number, we leave it out instead of guessing. Your engine’s decal and manual have the final say.

First, find your engine

The oil spec belongs to the engine, not the snow blower brand. Ariens’ Deluxe manual says the engine “is covered by a separate manual,” and its oil change step just reads “Refer to engine manual” (Ariens Deluxe manual, p. EN-15). Troy-Bilt’s Storm manual does the same (Troy-Bilt Storm manual, p. 16).

Look for the decal or stamping on the engine’s blower housing or valve cover. It shows the maker (Briggs & Stratton, Tecumseh, MTD, Toro, Ariens AX, Honda, LCT) and usually the displacement in cc. Then find that row below.

Gas and oil mixed in the tank? If your fuel cap says “50:1” and the engine has no oil fill cap or dipstick, it’s a 2-stroke. Skip to 2-stroke snow blowers.

What oil does a snow blower take? (by engine)

Engine (manual)Oil the manual namesTemperatures in the manual
Briggs & Stratton Snow Series 130000 / 150000 (manual, pp. 8, 13)Synthetic 5W-30 “for best performance.” Other detergent oil rated SG, SH, SJ or higher. No additivesBriggs: “Below 40°F (4°C) the use of SAE 30 will result in hard starting” (Briggs oil guide)
Tecumseh Snow King LH195, LH318, LH358, OH195, OH318, OH358 (manual, p. 4)5W-30, 0W-30 synthetic, or straight SAE 30. API SL/SJ. Never 10W-405W-30 about -20°F to 40°F. 0W-30 synthetic for the coldest days. SAE 30 only above about 32°F
MTD 357cc and 420cc, in Cub Cadet and Troy-Bilt machines (manual, p. 5)5W-30 or synthetic 5W-30. API SJ or higherSnow thrower chart: 5W-30 from about 0°F to 50°F. Synthetic 5W-30 from below -20°F to 50°F
MTD 179cc, 208cc and 243cc (manual, p. 6)5W-30 or synthetic 0W-30. API SJ or higherSnow thrower chart: 5W-30 from about 0°F to 50°F. Synthetic 0W-30 from below -20°F to 50°F
Toro Power Max 824 OE, SnowMaster 724/824 QXE, Power Clear 721 R/E (824 OE manual, p. 22)Synthetic 5W-30, 5W-30 or 10W-30. API SJ or higherSynthetic 5W-30 at every temperature on the chart. 5W-30 below about 45°F. 10W-30 down to about 0°F
Ariens AX snow engines (manual, p. 11)5W-30 “for general use.” Synthetic is acceptable. API SJ or higherNo chart. Ariens also sells a 0W-30 synthetic snow engine oil (parts list, p. EN-15)
Honda GX200, GX270, GX390 in HSS snow blowers (HSS724A manual, p. 15)SAE 5W-30 “for general use.” 4-stroke automotive detergent oil, API SJ or laterChart shows 5W-30 from about -20°F to 60°F
Husqvarna ST 224, 224P, 227P, 230P with LCT engines (manual, p. 24)SAE 5W-30“Below 0°C (32°F)”

Temperatures marked “about” are read off the manual’s bar chart, so they’re approximate. We didn’t find a snow-engine operator’s manual from Kohler, so it has no row. Use the manual that came with your Kohler engine.

How much oil does a snow blower take?

EngineOil capacity (manual)Change interval (manual)
Briggs & Stratton Snow Series 130000 / 15000020 oz (0.59 L), p. 18First 5 hours, then every 25 hours or once a year
Tecumseh LH195SA/SP, OH195SA/SP21 oz (0.62 L)First 2 hours, then every 25 hours or 3 months (pp. 17, 26)
Tecumseh LH318SA, LH358SA, OH318SA26 oz (0.77 L)Same as above
Tecumseh OH358SA28 oz (0.83 L)Same as above
MTD 179cc, 208cc, 243cc20 oz (600 ml)First 5 hours, then every 50 hours (p. 14)
MTD 357cc, 420cc37.2 oz (1,100 ml)First 5 hours, then every 50 hours (p. 12)
Toro Power Max 824 OE24 fl oz (0.70 L)First 5 hours, then yearly
Toro SnowMaster 724 QXE (model 36002)20 fl oz (0.60 L) (manual, p. 16)First 2 hours, then yearly
Toro SnowMaster 824 QXE (model 36003)24 fl oz (0.70 L)First 2 hours, then yearly
Toro Power Clear 721 R/E20 fl oz (0.60 L) (manual, p. 14)First 2 hours, then yearly
Ariens AX 136cc to 223cc16 oz (0.47 L)First month, then every 6 months. Every 40 hours if you run it more than 40 hours a year (p. 13)
Ariens AX 254cc20 oz (0.59 L)Same as above
Ariens AX 291cc, 306cc32 oz (0.95 L)Same as above
Ariens AX 369cc, 414cc, 420cc38 oz (1.12 L)Same as above
Honda GX200 (HSS724A)0.6 US qt (20 oz, 0.6 L)First month or 20 hours, then every year or 100 hours (p. 14)
Honda GX270 (HSS928A), GX390 (HSS1332A)1.2 US qt (37 oz, 1.1 L) (manual, pp. 48, 75 to 76)Same as above
Husqvarna LCT 208cc (ST 224, ST 224P)16 oz (0.47 L)After 20, 50 and 100 hours, then every 100 hours (p. 15)
Husqvarna LCT 254cc (ST 227P)20 oz (0.59 L)Same as above
Husqvarna LCT 291cc (ST 230P)32 oz (0.95 L)Same as above

Treat capacity as a ceiling, not a pour amount. Some oil stays in the engine after you drain it. Toro says “Do not pour the entire capacity of oil into the crankcase” (SnowMaster manual, p. 16). Ariens warns the other way: on some installs the total “could be as much as 4 additional ounces” because of the engine’s mounting angle (Ariens engine manual, p. 11). Either way, the dipstick decides.

Can you use 10W-30 or SAE 30 in a snow blower?

  • 10W-30: only if your manual lists it. Toro’s chart allows 10W-30 down to about 0°F. MTD’s charts list 10W-30 for its log splitter and tiller engines but not for snow throwers, so stick to 5W-30 or synthetic in an MTD-powered Cub Cadet or Troy-Bilt.
  • SAE 30: it’s a warm-weather oil. Tecumseh’s chart starts straight SAE 30 at about 32°F, and Briggs says SAE 30 below 40°F means hard starting. Your snow blower runs below freezing, so use 5W-30.
  • Synthetic: fine, and often preferred. Briggs recommends Synthetic 5W-30, Ariens calls synthetic “an acceptable alternative,” and Toro’s chart shows synthetic 5W-30 at every temperature.

Thick oil in the cold is a common cause of slow, hard pulls. Briggs’ troubleshooting chart lists “Incorrect oil” for an engine that’s hard to start and says to “Change oil to lighter viscosity (such as 5W-30)” (Briggs manual, p. 17). If yours still won’t go, work through our snow blower won’t start guide.

2-stroke snow blowers

Older single-stage Toros like the CCR 2450 and CCR 3650 run a 2-cycle engine (CCR 2450/3650 manual, p. 11). There’s no oil in a crankcase to check or change. The oil goes in the gas.

  • Ratio: 50:1 gasoline to oil. That’s 2.6 oz of oil per US gallon (80 ml per 3.8 L) or 5.2 oz per 2 gallons (Toro CCR 2450 GTS manual, p. 7).
  • Oil: Toro 50:1 2-Cycle Oil, or an equivalent oil certified NMMA TC-W. Toro: “do not use automotive oil (such as SAE 30 or 10W30) or fuel mixed at the wrong gasoline-to-oil ratio.”
  • Mix it in a can, not in the tank. Toro’s steps start with fresh unleaded gas in an approved fuel container, then the oil.

Never put 4-stroke motor oil in a 2-stroke’s gas. And never put 2-stroke oil in a 4-stroke’s crankcase: MTD says “Do not use non-detergent oil or 2-stroke engine oil” in its 4-stroke engines (MTD manual, p. 5). Check your machine’s fuel cap or decal for the ratio before you mix.

How to check snow blower oil

Check it before every use. Briggs, Tecumseh, MTD, Ariens and Honda all put it on the each-use list.

  1. Park on level ground with the engine off. Pull the safety key.
  2. Wipe around the cap, then pull the dipstick and wipe it clean.
  3. Put the dipstick back the way your manual says. This differs by maker. Honda says “Do not thread the dipstick in when checking,” and Toro’s SnowMaster manual says the same. Ariens and MTD’s 357/420cc engines say to fasten the cap, then remove it and read. On MTD’s 179 to 243cc engines, a quarter-turn cap is tightened until seated, but a threaded cap is not screwed in (769-11570, pp. 6 to 7).
  4. Read the level. It should sit between the marks: “H” and “L” on MTD dipsticks, “FULL” and “ADD” on Tecumseh. Engines with a fill plug and no dipstick, like the Toro Power Clear 721 and some Tecumsehs, fill to the point of overflow.
  5. Top up slowly if it’s low, a little at a time, and check again.

How to change snow blower oil

What you’ll need: the right oil (above), a drain pan, a funnel, rags, the wrench for your drain plug and a sealable container for the old oil. Browse 5W-30 small engine oil or an oil drain pan.

  1. Warm it up briefly. Toro and Husqvarna say to run the engine a few minutes first, because warm oil flows better and carries more contaminants. Ariens says to start from a cold engine and run it 1 to 2 minutes. Warm, not hot.
  2. Shut it off and pull the key. Disconnect the spark plug wire, as MTD’s manual says.
  3. Empty the gas if you’ll tip it. Briggs: when you tip the machine, “the fuel tank must be empty or fuel can leak out.” Toro says to siphon the tank or run the engine until it stops.
  4. Find the drain. It varies: – Toro Power Max 824 OE: an oil-drain cap on a drain extension. Slide the pan under it. – Toro SnowMaster and Power Clear 721: remove the drain plug and tip the machine backward (handle down) over the pan. – Honda HSS: the drain plug is on the right side of the engine. Hold the drain extension with a 17 mm wrench while you loosen the plug with a 10 mm. – Ariens AX: a 10 mm plug or 16 mm cap on a drain tube. Hold the tube with a 14 mm wrench so it doesn’t loosen. – MTD: the plug can be on the front or back of the block, or on an extension tube. Tip the engine so it drains from its lowest point. – Briggs Snow Series: remove the plug and tilt the snowthrower slightly.
  5. Reinstall the drain plug. Honda and Ariens call for a new sealing (crush) washer. Honda’s torque is 8.1 ft-lb (11 N·m). Ariens’ is 270 to 280 in-lb (31 N·m).
  6. Refill in stages. Toro’s method (our tip: it works on any engine): pour in about three-quarters of the capacity, wait 3 minutes for it to settle, check the dipstick, then add small amounts until it reads full.
  7. Recheck after a short run. MTD advises checking the level again once the engine has run and warmed up.

Never overfill. MTD warns that overfilling “may cause smoking, hard starting, or spark plug fouling,” and Tecumseh says it can cause oil carry-over into the equipment. Toro says if the level is too high, drain the excess before you run it.

Don’t confuse engine oil with gear oil. On two-stage Toros the auger gearbox takes its own lubricant: GL-5 or GL-6, SAE 80-90 EP gear oil, and not synthetic, on the Power Max 824 OE (manual, p. 21). Never put gear oil in the engine.

Why is my snow blower smoking?

White or blue exhaust smoke means the engine is burning oil. After an oil change, the two usual causes are too much oil and a machine tipped the wrong way.

SmokeLikely cause (source)What to do
White or blue, right after an oil changeOverfilled crankcase. MTD: overfilling “may cause smoking, hard starting, or spark plug fouling” (manual, p. 5). Briggs lists “Overfilling the crankcase with oil” (Briggs smoke FAQ)Check the dipstick on level ground and drain the excess down to the full mark
White or blue, after tipping it for service or storageOil ran out of the crankcase. Briggs lists “Turning/tilting the engine on its side for storage, oil change or any other reason” and running past a 15-degree angleSet it level. Briggs says the smoke should clear after a few minutes of running on flat ground
White or blue that keeps coming backWrong oil grade, a blocked or crimped breather tube, a crankcase air leak, a blown head gasket, or worn rings (Briggs FAQ)Check the oil grade against the tables above. If that’s right, it’s a dealer repair
A brief puff on the first start after storageOil put in the cylinder during storage prep. Honda: the engine “may smoke briefly at startup. This is normal” (HSS724A manual, p. 20)Nothing. It should clear

Tip it the right way. Briggs says that if you must tilt the engine, keep the spark plug facing up or the muffler side facing down, so oil stays in the crankcase. If your manual gives a direction, it wins: Toro tips its SnowMaster and Power Clear backward (handle down) to drain, and its Power Clear 721 manual warns not to tip the machine all the way forward onto its nose or fuel may leak.

Leaking oil? Check the drain plug first. Honda and Ariens both call for a new sealing (crush) washer when you reinstall it, and Ariens says the washer must go between the drain tube and plug “to prevent oil leakage.” On Ariens engines with a front drain, it also calls for Teflon tape or pipe sealant (Ariens engine manual, p. 11). An overfilled crankcase can push oil out too, so check the level.

Safety and the environment

  • Engine off, key out, engine cool enough to touch. Ariens’ maintenance rules start with the engine off, the spark plug cap removed and the engine cooled down. The muffler stays hot long after shutdown.
  • Spark plug wire off before you tip the machine or put your hands near the auger. If you’re in there because the auger stopped turning, see our auger not turning guide and the shear pin lookup.
  • Empty the gas before tipping, and do it outdoors, away from flames and pilot lights.
  • Wash used oil off your skin. MTD warns that prolonged, repeated skin contact with used oil may cause skin cancer, and says to wash with soap and water.
  • Recycle the old oil. Honda: “Put it in a sealed container and take it to a recycling center. Do not throw it in the trash, pour it on the ground, or pour it down a drain.” Many auto parts stores take used motor oil.

Doing an end-of-season oil change? Do it before storage, with the fuel taken care of. Our lawn mower winterizing guide and fuel stabilizer explainer cover the fuel side, and the same steps apply to a snow blower in spring. Before the first storm, run through how to start a snow blower. Checking the oil is step one.

Part of our snow blower maintenance guide: see the maintenance schedule for your brand, with each maker’s intervals from the manual.

Mowing season? See lawn mower oil for push and riding mower engines.

FAQ

Can I use 10W-30 in a snow blower? Only if your engine manual lists it. Toro’s chart allows 10W-30 down to about 0°F, but MTD’s snow thrower chart (Cub Cadet, Troy-Bilt) lists only 5W-30 and synthetic, and Ariens, Honda and Husqvarna list 5W-30. In freezing weather, 5W-30 is the safe choice.

How much oil does a snow blower take? Between 16 and 38 oz for most engines. Small engines (Ariens AX up to 223cc, Husqvarna LCT 208cc) take 16 oz. Mid-size engines (Honda GX200, MTD 179 to 243cc, Toro 724) take about 20 oz. Large engines (MTD 357/420cc, Honda GX270/GX390, Ariens 369 to 420cc) take 37 to 38 oz. Always finish by filling to the dipstick.

What’s the difference between SAE 30 and 5W-30 for a snow blower? SAE 30 is a single-grade oil for warm weather. 5W-30 flows like a thinner oil when cold, so the engine turns over and gets oil faster. Briggs says SAE 30 below 40°F causes hard starting, and Tecumseh’s chart only uses SAE 30 above about 32°F.

Can I use synthetic oil in my snow blower? Yes. Briggs recommends Synthetic 5W-30 for its Snow Series engines, Ariens calls synthetic an acceptable alternative, and Toro’s chart shows synthetic 5W-30 at every temperature. MTD and Tecumseh list 0W-30 synthetic for extreme cold.

How often should I change the oil in a snow blower? After the break-in period (2 to 5 hours on most engines, 20 hours on Husqvarna’s LCT engines, the first month on Ariens and Honda), then at least once a season. Briggs says every 25 hours or yearly, MTD every 50 hours, and Honda yearly or every 100 hours.

Sources

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top