Quick answer: When a snow blower won’t start, it’s usually one of two things. Either the fuel has gone bad (old gas gums up the carburetor), or a starting step got missed: the safety key isn’t all the way in, the fuel valve is closed, or the choke and primer weren’t used on a cold engine. Run the 5-minute checklist below first. If that doesn’t do it, find your symptom (won’t crank, cranks but won’t fire, or starts then dies) and go straight to that fix.
YardGuides may earn a commission from links on this page, at no cost to you.
The 5-minute checklist (no tools)
Do these in order before you take anything apart. They solve a surprising number of “dead” snow blowers.
- Safety key pushed all the way in. Most two-stage machines won’t start without it, and a half-seated key acts like an off switch.
- Run/stop switch on RUN (if yours has one).
- Fuel shutoff valve open. Many two-stage machines have a small valve under the tank. People close it for storage and forget.
- Throttle at FAST.
- Choke closed for a cold engine. Toro tells owners to close the choke fully in cold conditions or when the engine is cold. It can stay partly open around 30°F and up, and you don’t need it for a restart within about five minutes (Toro/Yardcare).
- Prime, but not too much. Primer counts vary by model and temperature. Toro’s guide says a couple of presses at 15°F or warmer and four below 15°F. Husqvarna’s says 3 presses below 0°F on its models. Both warn that over-priming floods the engine. Use the number in your manual.
- Fresh gas in the tank. If it’s last winter’s gas, skip straight to stale fuel.
Still nothing? Find your symptom below.
Diagnose by symptom
| What happens | Most likely cause | Jump to |
|---|---|---|
| Pull cord won’t pull, or is very hard to pull | Ice in the recoil, auger/drive engaged, oil in the cylinder | Pull cord stuck |
| Electric start does nothing | Outlet/GFCI, cord, starter button | Electric start |
| Cranks fine but never fires | Stale fuel, flooding, spark plug | Stale fuel, Flooded, Spark plug |
| Starts, then dies after a few seconds | Varnished carburetor, blocked gas cap vent | Starts then dies |
| Only runs with the choke on | Partly clogged carburetor jet | Starts then dies |
1. Stale fuel: the #1 cause
Gas doesn’t keep. Briggs & Stratton says “stale, untreated gas begins to break down after about a month,” and that stale fuel, dirt and debris are the most common reasons outdoor power equipment won’t start or run properly (Briggs & Stratton). Snow blowers have it worst because they sit for eight months of the year.
Most pump gas contains up to 10% ethanol. Honda notes that higher-ethanol gasoline “is corrosive and attracts water,” and tells snow blower owners not to use gas with more than 10% ethanol. It also says not to leave gasoline, with or without stabilizer, in the machine for more than 90 days of inactivity (Honda Power Equipment). Honda also points out that the small amount of fuel in the carburetor goes bad faster than the fuel in the tank.
Fix:
1. Work outside, engine cold, no flames nearby.
2. Drain the old gas from the tank into an approved container (a siphon pump makes this easy). If your carburetor has a drain screw or bowl nut, drain that too.
3. Refill with fresh gas, no more than 10% ethanol. Add fuel stabilizer if the can will sit for a while.
4. Try the checklist again. It may take several pulls to draw fresh fuel through.
Dispose of old gas at your local household hazardous waste drop-off. Don’t pour it out.
If fresh gas doesn’t solve it, the old fuel has probably left varnish in the carburetor. See starts then dies.
2. Flooded engine
Signs: a strong gas smell, and a spark plug that comes out wet. It usually happens after a lot of priming or a lot of pulls with the choke closed.
Fix (Toro’s method): open the choke (turn it off), pull the recoil cord 3 times to clear excess gas, then wait 15 minutes before trying again (Toro/Yardcare). Husqvarna says the same thing more simply: if it’s flooded, wait a few minutes and don’t push the primer (Husqvarna support). If the plug is soaked, pull it, wipe it dry and reinstall it.
3. Spark plug
Briggs & Stratton lists “disconnected, dirty or fouled spark plugs” as common causes of engines that won’t start (Briggs & Stratton).
- Check the spark plug wire is pushed firmly onto the plug. Snow, ice and bumps knock them loose.
- Remove the plug with a plug socket. Black and sooty, wet, or crusted means it’s time for a new one. Plugs are cheap.
- Set the gap to the spec in your manual. Don’t guess, because it varies by engine.
- To confirm you have spark, use an inline spark tester between the plug and the wire. It’s safer than holding a plug against the engine.
Buy the replacement by the plug number printed on your old plug or listed in your manual. Then search for that exact number, for example on Amazon.
4. Electric start not working
Most gas snow blowers with “electric start” use a 120V plug-in starter. It’s only there to turn the engine over, so it doesn’t fix fuel or spark problems.
- No sound at all: try a different outlet and check that the GFCI hasn’t tripped. Manuals differ on cords, so use exactly what yours specifies (some want only the supplied cord, others an outdoor-rated extension).
- It spins but the engine won’t catch: the starter is fine. Go back to fuel, flooding and the plug.
- Don’t hold the button down. Starters overheat. Toro’s guide says to crank five seconds at a time with at least 10 seconds between tries, and no more than 10 attempts. Husqvarna says no more than 5 seconds per try, with 5–10 seconds between. Check your manual’s limit and stick to it. When in doubt, use the recoil cord.
5. Pull cord stuck or hard to pull
- Auger or drive engaged: release both control levers. Some machines are very hard to pull with a lever held.
- Ice in the recoil housing: if it sat outside or came in wet, let it thaw in the garage for a few hours.
- Snow in the auger housing: clear it with a clearing tool or broom handle. Never use your hands, even with the engine off.
- Cord pulls a few inches then hard-stops, and it was tipped recently: oil may have run into the cylinder (“hydrolock”). Stop pulling hard. Taking the plug out lets the cylinder clear. If you’re not comfortable with that, it’s a shop job.
- Cord won’t retract, or snapped: the recoil spring or rope needs replacing. It’s a common, inexpensive part.
6. Starts then dies, or only runs on choke
This is the classic sign of a partly clogged carburetor. Old fuel evaporates and leaves varnish in the tiny jets, so the engine gets just enough fuel to fire with the choke on and starves when you open it.
A quick first try: with fresh gas in the tank, spray carburetor cleaner into the air intake and try again. If it runs, then dies again, the jets need a proper cleaning: remove the bowl, clean the main jet, and replace the gasket. We’re writing a full step-by-step carburetor guide, and we’ll link it here when it’s live.
Before you take the carb apart, also check:
– The gas cap vent. If the cap’s vent is blocked, the tank pulls a vacuum and fuel stops flowing after a minute. Test it by loosening the cap slightly. If the engine now keeps running, clean or replace the cap.
– The fuel line and filter (if fitted). Look for kinks, cracks or a clogged inline filter.
Brand notes
Most consumer snow blowers share the same basic engines and fixes, but controls differ. Always check your own manual, which you can find by model number on the manufacturer’s support site.
Craftsman, Cub Cadet, Troy-Bilt, Yard Machines (MTD)
These brands come from the same corporate family. Stanley Black & Decker completed its purchase of MTD (Cub Cadet, Troy-Bilt, Yard Machines) in December 2021 and also owns Craftsman (Tractordata, Wikipedia). Many of these machines use similar controls (safety key, primer bulb, choke knob, fuel valve), so the checklist above applies directly.
Toro
Toro publishes its starting procedure, including primer counts by temperature, choke settings, electric-start limits and a flooding fix (Toro/Yardcare guide). Some Toro models have different controls, so check the manual for yours.
Husqvarna
Husqvarna’s support site has model-family starting instructions. The fuel valve and primer steps apply only to some models (Husqvarna support).
Honda
Honda is the strictest about fuel: no more than 10% ethanol, and no gas left in the machine for more than 90 days of inactivity (Honda).
Ariens and others
The same symptom-first approach applies. Look up your manual by model number for primer counts and electric-start limits.
When to take it to a shop
Get a pro if you see any of these:
– Fresh fuel, good spark and a clean carburetor, and it still won’t fire. That points to low compression or an internal problem.
– Metal-on-metal noises, or the engine locks up.
– Oil in the cylinder that keeps coming back.
– You’d rather not open the fuel system. That’s a reasonable call, and a shop tune-up is usually cheaper than a new machine.
Prevent it next year
Fuel is the most common culprit, so handle it at the end of the season:
– Either add stabilizer and run it a few minutes so treated gas reaches the carburetor, or run the tank dry. Honda goes further and says not to leave gas in the machine more than 90 days.
– Change the oil per your manual.
– Store it dry and covered.
The routine is almost identical to the one in our guide on how to winterize a lawn mower. If your mower won’t start come spring, see our Toro Recycler 22 won’t start troubleshooting guide, and if you have a Kohler-powered machine, read about Kohler Smart Choke problems.
What you’ll need
- Fuel stabilizer, or ethanol-free canned small-engine fuel
- A replacement spark plug (match the number in your manual) and a plug socket
- An inline spark tester
- Carburetor cleaner spray
- A siphon pump and an approved gas can
FAQ
Why won’t my snow blower start after sitting all summer?
Almost always fuel. Gas left in the tank and carburetor since spring has broken down. Briggs & Stratton says untreated gas starts breaking down after about a month. Drain it, refill with fresh gas, and if it still won’t run, clean the carburetor.
Why does my snow blower only run with the choke on?
The carburetor’s main jet is partly clogged with varnish, so the engine only gets enough fuel with the extra richness the choke provides. Cleaning the carburetor usually fixes it.
Why does my snow blower start and then die?
Usually a partly blocked carburetor. A blocked gas cap vent is a cheap thing to rule out first: loosen the cap slightly and see if it keeps running.
How many times should I prime my snow blower?
It depends on your model and the temperature. Toro suggests a couple of presses at 15°F or warmer and four below that, and Husqvarna says 3 below 0°F for its models. Too many presses floods the engine.
Can old gas ruin a snow blower?
It can leave varnish that clogs the carburetor. It’s usually fixable with a carburetor cleaning or replacement, but prevention is far cheaper.
Sources
- Honda Power Equipment, Snow blower fuel recommendations
- Briggs & Stratton, Small engine problem solving tips
- Toro / Yardcare, How to start a snow blower
- Husqvarna, How to start the engine (electric start)
- Tractordata, Stanley purchases MTD
